Partnered Output Coils - Free Energy

[stupify12]

 Hello,

       This coil is not new, Tesla used this winding coil on his Tesla Transformer on the Tesla Book. Together with the detailed construction of this transformer it is very clearly describe on the Tesla Book.

The Partnered Coils which what you call it which actually I think is a Cylindrical form of Tesla Pancake Bifilar Coil.. The Cyclindrical Form Tesla Pancake  (Parntnered Coil) can be driven with TWO Primary but not on the same core, which Tesla design it in a wooden spool, that is why Tesla clearly showed the schematic of this Tesla Transformer with a Dual Primary but not connected in series, will only be connected when the small spark gap fires between the Dual Primary..


Meow

[EMJunkie]

Hello,

       This coil is not new, Tesla used this winding coil on his Tesla Transformer on the Tesla Book. Together with the detailed construction of this transformer it is very clearly describe on the Tesla Book.

The Partnered Coils which what you call it which actually I think is a Cylindrical form of Tesla Pancake Bifilar Coil.. The Cyclindrical Form Tesla Pancake  (Parntnered Coil) can be driven with TWO Primary but not on the same core, which Tesla design it in a wooden spool, that is why Tesla clearly showed the schematic of this Tesla Transformer with a Dual Primary but not connected in series, will only be connected when the small spark gap fires between the Dual Primary..


Meow

@stupify12

Have you read the pdf document?

I just posted, asking everyone here that wants to participate to do their homework: http://overunity.com/15395/partnered-output-coils-free-energy/msg433154/#msg433154

PDF URL: http://www.hyiq.org/Downloads/Guidelines%20to%20Bucking%20Coils.pdf

In Video Form: https://www.youtube.com/watch?v=zSadMqEnO7I

You're right, its not new, but again I have already pointed this out in the documentation. Its not anything like the Pancake Coil!

Please study the data! It is really important!

Kind Regards

   Chris Sykes - hyiq.org
   To Reach New Horizons!

[wistiti]

Hi emJunkie(sorry for em freak...)
Could you explain a bit more on the charge separation? Also could you post a schematic of a low cost way to pulse the primary coil at the right frequency?
Thank you!

[EMJunkie]

Could you explain a bit more on the charge separation?

Hi Wistiti,

Good Question!

See: https://www.youtube.com/watch?v=lcGWO_x8tpM - @4.46 on I cant Stress Enough how important the study of this video and other material is!!!

Magnetic Flux as it cuts (Bvl), or in Flux Linking(dPhi/dt), each turn sees a change in Flux Density over time, the Conductor (Turn/s) experience's a Force.

The Force is the Lorentz Force:  http://en.wikipedia.org/wiki/Lorentz_force

I have shown two experiment's to show more information in this area: https://www.youtube.com/watch?v=kckxzBUxTHg and https://www.youtube.com/watch?v=P3Enr6_d3yU

Charges in the Conductor are separated because of the Lorentz Force. Positive one way, Negative the other!

I have proven this, in this video: https://www.youtube.com/watch?v=P3Enr6_d3yU

Induction does not occur unless the Charges are pushed the right ways! it is possible to push the Charges in the same ways at the same time, which results in no Output EMF!

Please study the videos carefully. Information is not always in the form of verbal context!

Also could you post a schematic of a low cost way to pulse the primary coil at the right frequency?

I recommend to try to do it as cheap and easy as possible. I use a H-Bridge in the video. Driven by a small Micro Controller. I have spent far too much time and money in my configuration, to make this practical however!

Something that may be suitable:

EBAY: http://www.ebay.com.au/itm/Dual-H-Bridge-DC-Stepper-Motor-Drive-Controller-Board-Module-Arduino-L298N-BY-/200991688684?pt=AU_B_I_Electrical_Test_Equipment&hash=item2ecc09c7ec

or

EBAY: http://www.ebay.com.au/itm/43A-H-Bridge-Drive-PWM-For-Arduino-Semiconductor-BTS7960B-Stepper-Motor-Driver-/380802365419?pt=AU_B_I_Electrical_Test_Equipment&hash=item58a996f7eb

Look at the frequency range before purchasing. Anything from 50Hz to 5KHz will do the trick.

Even a simple Home made bridge will do the trick, I personally think its too much work for the cost. when one can get something that will be close enough for $3 on EBay.

Maybe use a Signal Gen to drive the Bridge.

Does this answer your questions?

Kind Regards

   Chris Sykes - hyiq.org
   To Reach New Horizons!

[vasik041]

Hi EMJunkie,Thank you for sharing many interesting files.
Perhaps you could suggest some (simple) experiment to observe COP > 1 ?
I (and my friends) made many experiments with coils with opposing magnetic fields and so far we can't see reliable proof that such arrangement give OU.
Thanks!