Successful TPU-ECD replication !

[acerzw]

@all

anyone like to lay claim to 'Otto TPU 2' then? or Innovation was that previous post 'I had to do it' you admitting it was you?

Acerzw, puzzled

[innovation_station]

nope not my vid

i was talking about the song 

lol!!!

is

just watched the vid it was made by camster i think he has left this site now but he has made a few vids that is his work

[13thHouR]

@ pauldude000

Have you considered re-running your calculations using caduceus coils instead?

ignoring the rather unusual things associated with them, there are 3 factual bits of data.

1. They are very efficient at Soliton wave production.
2. They have almost infinite resonance.
3. (more dangerous aspect) their signals are capable quantum tunnelling with very low energy input. Which rules out most faraday cage set ups.

Of Which all 3 are very important factors in the TPU production.

Although it is rather more complex to isolate the ideal length, cross overs and repeat windings with this type of approach. I did notice just using the output from one of my function generators (not secondary power source), I was getting like for like in the collector. No loss of Energy at all. I am continuing to experiment with variations of the caduceus and true mobius setup   (A proper mobius loop rather than just inter connected loops).

Having to run mA tests because the shielding involved for testing higher powered caduceus coil is an astronomical price. So far the 50 and 180Khz are showing promising results.

According to amount of crossovers I have had them resonating upwards of 22Mhz (for 450Khz input). For only 6 feet of PVC multicore bell wire on single wound Caduceus coil..

I love those pretty patterns...... No I have not been smoking something that I shouldn't be LOL   Caduceus coils have seriously complex harmonics, check them out on an Analogue scope (or very good digital one) and you will see what I mean.

I need to invest in a new spectrum analyser. damn they got expensive lately.



btw On otto's set up raising, the inner collector about 2 inches above outer does increase the efficiency.

[otto]

Hello all,

@IS

how does it go??? My answer - good.

@Paul

There is really NO need to appologize!! In the video we see a REPLICATION of my TPU: Thanks for the video. I saw it the first time. Fine video. This guy (comster?) connected a bulb and when his light is brighter, when he changes the frequency, the current rises and in my newest coils the current dropps when my light is brighter.

Its really time for me to begin to wind controls as our master told us: all around the collector ....in segments....
My biggest problem is that every few days I have to make new controls because they are "burning". I have again 2 shorted controls because there is a heat and the current....

I can only hope this guy in the video used a 100W bulb!!!

Otto

[pauldude000]

@otto

First, you want to see steve marks inspiration on the bifiliar control coils? Hmmm...?

Here is the original, and if you read the reasoning for figure 2, you will quickly understand. I would bet money. It is the original bifiliar with a mobius or endless loop winding.

http://www.magnetricity.com/NeoG/Bifilar.php

Second, in the video i hate top say, but the bulb looked suspiciously like either a 25 or 40 watt refridgerator bulb to me. Refridgerator bulbs tend to have the super small clear globe to fit into the restricted space. However it is possible that it was a small globe bulb built for use in a cieling fan too, though it looked smaller than these to me. With only the socket, there is little scale to measure visually against.

No matter how you cut it, his coil was resonating far too low.

Just for giggles, wind your control coils bifiliar/mobius in the manner described in the link, remembering that it does not have to be a pancake as it can be wound conventionally. Regular coil wrapped bifiliar/mobius in three sections...... Each section length tuned approx. to a specific frequency. Can be done cheap using el-cheapo tiny diameter zip cord speaker wire, or even four strand flat phone cord. (I am talking cheap stuff here!  )

The phone cord might be better, as you could hook two in mobius, and two as mutually re-inforcing parallel drives. Try them ungrounded before you try them grounded too. (Just a whim.)

If you do, be sure to let me know the effects!

Paul Andrulis