Successful TPU-ECD replication !

[z_p_e]

Koko,

You are being reasonable, as I feel I am being too.

However, the other school of thought feels they are being reasonable too. There's no reason why we can't coexist is there?

We have different opinions and approaches. One side will never convince the other, so perhaps let's just call a truce, and let both sides proceed as they will.

In the end, hopefully the answers will be revealed, and the issue settled once and for all.

Darren

[chrisC]

darren & koko:

Good point Darren. We're here for a reason. To seek the truth and there is only one truth. Ya?

So, let us all work together, build some TPU's and contribute our resources.

Cheers

chrisC

[hartiberlin]

Hi All,
just got an email from Jason,
telling me, that he only got 1.5 hours sleep last night and that he has
to work on some school exams in the next days, so it will take
some time, until he gets again to his TPU-ECD.
So please be patient with new measurements from him.

Regards, Stefan.

[bob.rennips]

Whilst waiting on the exact driver as used by Jason I thought I'd do a couple of tests.

I wanted to see if I could capture what was happening, signal wise, when say a 90khz and 180khz was 'mixed' in a coil.

To do this I wrapped a standard solenoid coil. This is the mixed signal coil. On top of this two parallel wires wrapped together to produce another two coils. i.e. As if wrapping a bifilar coil.

Into the two parallel wrapped coils I fed 90hz into one and 180hz into the other. The attached image shows the 180hz on the top trace, the 90hz I've drawn in in red, the bottom trace is the resultant output. The drawn in red line on the lower trace is the 0V level.

The staircase on the output goes down because the input signal are synchronised on a rising edge. I'll try moving the input signal to synchronise on the trailing edge so that the staircase goes up.

If this output were DC shifted up say 100V, you would have a situation where, in the case of a rising staircase, you would have progressive dc pulses WITHOUT A CURRENT REVERSAL. We know from Tesla that Radiant Energy occurs when pulses are applied in such a way that their is no current reversal... Further more, if this staircase effect was to occur on a high voltage spike, due to further mixing with other coils and you have the situation where you are generating high voltage DC, non reversing pulses.

I think part of the puzzle is to get this staircase effect happening on the leading edge of very high voltage BEMF pulses.

EDIT: I had the AC button pressed on my scope instead of the DC. I've therefore redrawn the 0V level on the attached image. The 0V level is at the bottom of the lower trace NOT centered on the lower trace.

[Merkhava]

Hi All,

As for me and my thinking of this, the goal of the project to replicate the TCU is NOT to make reward money or figure out who gets control or fame for it. Let the Most High God figure all that out for us when the proper time comes.

This project is about changing the world. The current modern paradigm based on the use of fossil fuels  as energy and chemical explosion as our machinery prime mover... well, let's just say it is a tragic dead end waiting to devastate us. Peak global oil production has probably already occurred, but demand for oil is increasing exponentially as China, India, and much of the Third World modernize. They are seeking the same resources we have cheaply taken for granted for the last 100 years.

If the fossil fuel paradigm remains unchallenged by any new energy technology, then we are headed for more devastating wars (like Iraq) and an eventual, rapid and very harsh economic decay that will put us all back to riding horses and camels again. This could all happen within our lifetimes at the current rate demand growth compared to energy production. See the attached Peak Oil PDF.

Now I know... this particular thread is all about replication and experimental facts, so this will be my last "speech". But I must say replication for the sake of replication is not enough. We must do replication with an inspiring vision. It must be a bigger vision than just some invention for our own selfish enrichment and ego stroking. We must have a vision of saving our world and pushing human civilization further along to newer heights for the sake of our children and our children's children. The world has more than 6 billion souls. Consider your own education, profession, income and individual wealth and most of us in this forum are probably representing the top tenth percentile compared to the rest of the total human population. If we can not find the altruistic motivation and illumination to pursue a lofty vision for the future that is greater than ourselves, then what can we expect of the other 90% of our neighbors on this planet? So let us replicate this technology with vision, with purpose and with passion!!

We must shift the paradigm from a fossil fuel basis to a Radiant Energy paradigm. And when success is truly in our hands, then let us virally spread it throughout the world like a new "gospel" using face to face interactions and the wonderful internet technology that we have available to us. Let us change the world and free ourselves from the poverty, misery and warfare brought to us by Dirty Oil!

I for one have been supremely inspired by SM's videos and also Otto-Roberto's and Jason's recent replications. I will work on this myself. And as I achieve my own success I will no doubt give this knowledge away and teach it to anyone willing to listen.

May God help us all in this endeavor!
Robby