Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Bob Boyce TPU thread

Started by hartiberlin, July 26, 2007, 12:03:41 PM

Previous topic - Next topic

0 Members and 2 Guests are viewing this topic.

hartiberlin

This is the Bob Boyce TPU thread.
Stefan Hartmann, Moderator of the overunity.com forum

Bruce_TPU

Build Page 1

The Bob Boyce Toroidal Power Unit Replication Parts List and Suppliers

1.  Core -  T650-52

Micrometals, Inc. Home Office

http://www.micrometals.com/contactus_index.html

Address:  5615 E. La Palma Avenue
Anaheim, CA 92807 USA

Phone:
714-970-9400
Toll Free in US:
1-800-356-5977
Fax:
1-714-970-0400
E-Mail:
sales@micrometals.com

2.  Bee's Wax
Toilet bowl wax seal from your local building supply store

3.  Bias Winding
This winding is 48 turns of 20 guage magnet wire on this particular core.

4.  Winding tape
Can be obtained from suppliers that carry electric motor and transformer rewind supplies.
Surplus source for electrical winding tape:

http://www.surplussales.com/RF/RFTeflon-Mylar.html

The yellow, non-stretchy, thin stuff is polyester (Mylar is a brand name - of 3M - I think) - look for the yellow roll on the page.  These prices are a little cheaper than standard pricing.

5.  Woven fiberglass sleeving
Skycraft Parts & Surplus  (See #6 for contact information.)

6.  Secondary winding
a.  16ga solid copper, silver coated wire.  Somewhere around 90' or so. 131 turns seems to fit well. A bit more turns if no longitudinals are wound underneath. 

Skycraft Parts & Surplus
Business Hours (E.S.T.)
Mon-Fri: 8:30 - 6:00 p.m.
Saturday: 8:30 - 5:00 p.m.
Sunday: Closed

Skycraft Parts & Surplus
2245 West Fairbanks Ave.
Winter Park, FL 32789

Tel. (407) 628-5634
Fax (407) 647-4831

b.  Home Depot for some 0.080" weedwacker line. This was cut into 133 little pieces 1.5" long each.

c.  Vitamin C powder bottle

7.  Secondary Winding Tool
I had to make up a small spool that could pass through the toroid hole. This was made from a 3 1/2" long piece of 1" electrical PVC tubing solvent welded to a couple of 2 3/4" diameter discs. These were cut from 1/4" PVC sheet. I turned these on the lathe so they would fit over the ends of the tubing.

8.  Primaries (3 or 6.  Recommend 6 primary windings)
20ga solid copper, silver coated wire

Same source as #6 above


Hex Controller
(Future Information)
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

Bruce_TPU

Build page 2

The Bob Boyce Toroidal Power Unit Photo Journal



All future updates will be able to be downloaded from this post:

Please download the newest Bob Boyce Working Toroidal Power Unit > V.1.5.PDF
located at the bottom of the page!



1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

Motorcoach1

Thank youÃ,  Stefan and Bruce -Ã,   now it will be eseryer to keep updating on progress.Ã,  toroids are ordered and still searching for silver wire and getting all parts for PCB board. in Bobs form i have the PMW#3 and he mentioned something about specific parts that fit the board is that still a go?Ã,  I know this is a new PCB board but does the parts issue still apply, Mike    PS -to all put a short cut on your desk top to this thread and go strait to the thread :)

MarkSnoswell

Excelent -- a private space :)

I have a core now but am about to run out of time untill September. I will be availble on-line but because of business travel I wont be able to experiment.

I do hope to get a few hours this weekend to do some basic experiments on longitudinal wave transmission -- I have a stack of long solenoid coils (for various tesla coils) laying around that I want to do some tests with. As it's a capacitivley coupled advanced wave we want I have some ideas I want to test for more efficent drives... I'l post some photos whatever happens.

cheers

Mark.
Dr Mark Snoswell.
President of the CGSociety www.cgsociety.org