Stanley Meyer replication with low input power

[LtBolo]

Do you chew up everybody you meet this way? You really have a chip on your shoulder...that ain't healthy.

I have 2 full time degreed engineers working on this. We have built two large cells and a half dozen small ones. We have built about 10 versions of the power supplies and tested them on cells. Using actual scientific method...rather than the usual wild-eyed-post-it-to-youtube crap...we have not seen any results worth sharing or I would have done so. Virtually everything I have observed has convinced me that the current theories are incomplete, which is why I came here...to talk about alternative theories of operation with other folks who have first hand knowledge, and would really love to have discussions with those that can demonstrate performance beyond Faraday.

Never in my wildest dreams did I envision that I would end up being branded as I have and encouraged to leave. Remarkable. Given the odds against you, I'd think that you would want folks with resources to invest helping you, and that you would welcome them. Dude, I'm not Big Oil or MIB. I'm a good engineer that's managed to make a few bucks doing what I love, that desperately wants to see a world where we don't fight wars over fossil fuels or subject the sovereignty of this country to others for resources. Take a Valium.

For what it's worth, if there are any folks other than the warm and welcoming Ash that would like to discuss alternative theories other than aetheric energy and water cracking...perhaps along the lines of how the so called 'conditioning' process may be creating the conditions necessary for a fusion type reaction or how acoustic resonance might be creating a cavitation type reaction, I would still love to have that conversation.

[ashtweth_nihilisti]

No chip, and did not intend to "chew" any body up. My apologies if you have this impression. I am trying to steer you in the right direction, it may not agree with your business intensions, but none the less it is genuine.

>I have 2 full time degreed engineers working on this.

I am sure you would share your open source results with us after you make some money right?
4get this small chat man, if you are building then build and report, people need to leave money or skepticism out of this thread , we don't care. It the reasons why this technology remains suppressed.

How do i know the advice we give you stays in the public domain if you test it? i don't,..until you prove your self like the engineers i know have, then ill remain a little skeptical when you come in here and talk about big business, and skepticism. We need neither to get results. I hope you prove your self.
Carry on and chat about your replication and ideas, we are very welcoming and interested. But not in other themes.

Ash

[fever16]

guys stay on topic.
@LtBolo
you might have build some really interesting.but ppl will only believe you if you share your research here.just some pictures will do the job.
if you don't want that,pls start another thread.the whole talk of believing or not believing make new commers frustrated.
finally i don't know whether this whole thing will work or not.but iam still interested in spending my time over this project.
i believe we will come up with some thing like water spark plug guys did.

[ashtweth_nihilisti]

Guys an update, we will be keeping our original RAVI cell as is and conditioning it for 2 more months, the new RAVI cell, will ave slots embedded, and also Derlin and the ultra violet lights to help fracture

We have not added in the VIC in to the old cell, so looking forward to some snaps soon.

Here is new info given to me, for what is worth.

"Message: I have duplicated Stan Meyer's work, and have taken it
several steps forward. First, during assembly of the generator, I have
found that you must "tune" the tubes to the same pitch. I do
it with a simple guitar tuner. Just clip it to the tube and strike it
with a small brass (to prevent polarization) hammer. The easiest way
to change the pitch, it's always the outside tube, grind a notch in it
like Stan did. Second, oscilate it with high voltage, low amperage
voltage. Water resonates at 926khz, and will disassociate at that
range. Before conditioning the generator, briefly dry modiluate it in
5 second bursts, with about 2 min between bursts for about 10 min. You
should be able to hear it hum, and with a practice ear, tell if one
set is out of picth. I also added a toroid coil, to produce
parahydrogen. Tube size is determined by the diameter of the cell, be
it 4, 5, or 6", but the optimum gap between tubes should remain
.045 to .060. Try to maintain the low side. You are correct, in that
it takes at LEAST 2 to 3 months to condition your tubes. I don't add
the toroid until final assembly, and try to maintain a 1/8' gap from
the top of the tubes to the toroid. I am currently running 70psi in
the generator.

Several other things I am working on are a plasma spark plug/injector,
and am expiermenting with an 85 Chevy S-10 motor. I have it stripped
down, and have machined smaller pistons, to allow for a ceramic coated
dry sleeve. Another hurdle that must be crossed is how to ceramic coat
the cylinder head to impede hydrogen saturation, without warping the head.

If you have questions, you may reach me by email only. I have had 3
security breaches, and must be VERY careful. I might add that I am
leary of sending this email, but in light of what has happened lately,
I don't want my research to be lost."

[fever16]

thanks for the update.
but i always had a doubt abt this conditioning.
we are doing it to remove the impurities from tubes right.
to confirm this point what i did is,2 pipe sets of same material and same length but used different waters.
one is pure DM water(distilled with no minerals at all) and another just river water.
the jar with river water produced heck lot of red musk.the other jar stayed clean with very little bubbling.
this confirms that impurities are from water not from tubes.

if the coating over tubes is to increase capacitance factor,then what jnaudin did is right.cover your inner electrode with thick layer of ceramic coating or plastic.