Stanley Meyer replication with low input power

[rapttor]

@ Dankie, is it your goal in life to start fights on every single forum you can get on? Stop showing your age for once, and start reading between the lines and listening to what some of these guys have to say. There are folks on here that have forgotten more information than you know, show a little respect... it just might work in your favor.


-rapttor

[Crush]

@ Dankie, is it your goal in life to start fights on every single forum you can get on? Stop showing your age for once, and start reading between the lines and listening to what some of these guys have to say. There are folks on here that have forgotten more information than you know, show a little respect... it just might work in your favor.


-rapttor

I agree that Dankie has an attitude problem and doesnt respect other people enough  , everybody agress on that . But I dont pay attention to it anymore , the kid just wants some attention    At least he is bringing something to the table , unlike alot of people who constantly spread bull .

Honestly its all good to me ,  I couldnt give a crapshoot as long as we making progress with this technology , this is all that matters really , everbybody has his own personality 

[froarty]

Another clue re the geometry of materials at the microscopic from
today's Science Daily - sounds like the aluminum has to be cleaned to repeat the trick but they are looking to see if it can be close looped.....
http://www.sciencedaily.com/releases/2009/01/090122141230.htm

[Grumpy]

So one of my customers probably contacted Ashtweth , I have no connection to Ash and often insulted him @ energeticforum.com . But thx Ashtweth for defending a good cause , you are finally seeing the truth .

@ Grumpy

Seriously I wonder what is it you do here , you have no work to show , no useful info , besides sharing your opinions what is it you do here  ? Cant you see I'm trying to build something positive here , but you would rather trash me because its more important for you to be right and feel smart then solving this Meyers's thing . Do ya  you see this is more important than you being right , in that little mind of yours ? DO YA

How bout some encouragement grumpy ??

Everybody who works hard @ it deserves this technology , its you that is being left behind .

I wasn't trying to cause a flame war with Ash, just calling out the BS.

The so-called Meyer Mystery was solved a long time ago, Dankie.  Sorry if you guys missed it.  Buzz is explaining it quite well, I suggest you pay attention. 

What do I do?  I bring together bright minded people.  Like a recruiter.  Aside from that I solve problems and dispel bullshit.  I am not here to teach anyone, or prove anything.  I only share with those I know well - you just can't trust people these days.

Dankie, I remember you from EBN.  I have hundreds of posts, but you can only see a handful of them.     You just don't know, what you just don't know.

I didn't trash you, Dankie.  I made sure you knew that the permeability goes to crap if the 403FR is not annealed and many wire materials are not annealed.  If it is "springy" it is not annealed.  Also, you mentioned that the voltage across the coil is very close so it will not arc, but 40kv will arc to the core and from that to other coils.  Even 20kv can do this.  Above 10kv corona becomes important.  Your poly-a insulation will hold back 10kv - this is the same I have on a few coils - unless there is a field concentration or a nik in it.  40kv and you may want to vacuum pot it in a dielectric.  See, you are pulsing and if you calculate the pulse length along the wire you get a large variation in potential inside the coil.  Time is a factor, so longer pulse stresses the dielectric differently than a short pulse.  There are several modes of polarization for a dielectric - determined by the length of time that the force is applied.  Things just aren't as simple as they first seem.

Any magnetic wire with a fair amount of resistance will help, but it is not required.   there are many ways to achieve the same results.  The reasons behind this choice of materials is far more important, and few seem to care about that.

I noticed your apology to Fritz.  That was a good thing to do.

Many people have good intentions in trying to build something, but most are cocky pricks and don't listen very well.   If your intentions were totally genuine, then you would not have gotten kicked of a forum recently.

[dankie]

I wasn't trying to cause a flame war with Ash, just calling out the BS.

The so-called Meyer Mystery was solved a long time ago, Dankie.  Sorry if you guys missed it.  Buzz is explaining it quite well, I suggest you pay attention. 

What do I do?  I bring together bright minded people.  Like a recruiter.  Aside from that I solve problems and dispel bullshit.  I am not here to teach anyone, or prove anything.  I only share with those I know well - you just can't trust people these days.

Dankie, I remember you from EBN.  I have hundreds of posts, but you can only see a handful of them.     You just don't know, what you just don't know.

I didn't trash you, Dankie.  I made sure you knew that the permeability goes to crap if the 403FR is not annealed and many wire materials are not annealed.  If it is "springy" it is not annealed.  Also, you mentioned that the voltage across the coil is very close so it will not arc, but 40kv will arc to the core and from that to other coils.  Even 20kv can do this.  Above 10kv corona becomes important.  Your poly-a insulation will hold back 10kv - this is the same I have on a few coils - unless there is a field concentration or a nik in it.  40kv and you may want to vacuum pot it in a dielectric.  See, you are pulsing and if you calculate the pulse length along the wire you get a large variation in potential inside the coil.  Time is a factor, so longer pulse stresses the dielectric differently than a short pulse.  There are several modes of polarization for a dielectric - determined by the length of time that the force is applied.  Things just aren't as simple as they first seem.

Any magnetic wire with a fair amount of resistance will help, but it is not required.   there are many ways to achieve the same results.  The reasons behind this choice of materials is far more important, and few seem to care about that.

I noticed your apology to Fritz.  That was a good thing to do.

Many people have good intentions in trying to build something, but most are cocky pricks and don't listen very well.   If your intentions were totally genuine, then you would not have gotten kicked of a forum recently.

Well thats what pissed me off in the first place with EBN , they dont let you see all the site lol , isnt that the gayest thing ? I asked Stevie if there was anything special and he said no , I may have been rude a bit and I apologize ...

In this post you can see the email from carpenter .

http://waterfuelcell.org/phpBB2/viewtopic.php?t=1185