Steven Mark`s TPU

[giantkiller]

Hmmm...

3 cannons or 3 sequencial accelerator rings like found in old Trinitrons?

This would be more like another project - The BFG2000 

In the previous tube schem I see that the control coils are at one end of the collectors. In Roberto's last pic I see the controls in the center. In reference to the BFG, I have two controls per collector segment. Each pair will be fired in opposite directions from the center outward. 3 layers = 9 segments = 18 controls. Look!? It's an ECD. No. It's a TPU. No. It's a stun gun? Well it's just another version of Tesla's Ionizer. Wrap it, fire it, connect it any way you want. They can all be dangerous.

Way to go guys!

@Roberto,
Put a piece of tape in front of your mike and camera. There is an CRSS feeder running. Happened to me. I just spent 2 1/2 days scrubbing malware off.
If you want to go further then get an open window and a bullet. That will insure the pc doesn't come back inside the house once you throw it out...

--giantkiller.

[Frederic2k1]

Sorry for being a bit off-topic, but in the topic "Working Magnetic Motor on you tube??" on the mechanical-setups - forum, there is a video shown, which perhaps shows us what we try to catch up with our rotating-magnetfield in our TPUs:

http://www.youtube.com/watch?v=I4B_Lj1JM6g

"Natural Harmonic Magnetic Communication Principles..."

sorry again for ot.

kind regards

[ronotte]

@GK,

THANKS for the suggestions about mike & camera!  You know: I thought about this some time ag?!!

About the control-coil on my last pic: pay attention... as the dranwig may be misleading as I draw them in the middle of the rings only for not clobbering the schematic (already full of wiring...). Actually they are spreaded all along the circumference as depicted on 3StackTPU picture posted earlier in this thread.

Roberto

[wattsup]

@Roberto

I found this guy on ebay that makes Tesla coils that I think I will order one of 4" x 24" just to do some other HV tests. But what caught my eye was the text description that I am copying here;

*****************************

The Ultimate 4 inch clear acrylic form, wrapped with  25 AWG Hi Temp 200C wire. It doesn't get any better than this one. 1000 turns, wrapped 20 inches on a 24 inch X 4 inch form. 1050 feet, with a resonant frequency of about 242 Khz @ 1/4 wave.  Further  Sealed with several coats of Polyurethane.   It is a steady tension wound coil with no gaps, kinks or flaws.

******************************

As shown, the resonant frequency of this rather big air coil is about 242Khz, about the same resonant frequency you are working with. Do you think there could be a relationship between this Tesla coil and the TPU, but how can a huge coil and a small TPU have the same resonant range?

[BEP]

@Ronotte

While your scope shots tell me you have the 'kind' of resonance I talk about (the 2 or three sines after the pulse) like most I am interested in eliminating all unexpected causes. To that end I have a question: Do you think it is possible this 22.222kHz may be the result of an LC tank created with the secondary winding of the isolation transformer?

I don't have your exact type of transformer but I have been experimenting with a 1:1 isolation transformer (iron core but low grade unshielded). The secondary plus a low value capacitor resonate easily in the 25 kHz range. Since your collectors are Mobius the coil capacitance can be extremely high with almost no inductance....... This may start another flame war but we may be looking at 'reductance'. Also another term not generally found in the books.

>>EDIT:
The reason for my wondering about reductance is I'm finding it is possible to vary the resonance of a spiral wound collector by changing the amplitude duty-cycle and PRF of the perpendicular wound control coil. This using the current dip method of locating resonance.
<<

@Frederick2k1

Yes. This man has it together on magnetics. If he ever explains what is going on and how to do it.... Well, I hope he succeeds.