Muller Dynamo

[xenomorphlabs]

The switch only controlled the drive coils. The stator coils are still happily converting the kinetic energy of the rotor into plenty enough energy to keep the DC to DC happy with no load. No magic there.

RomeroUK doesn't remotely seem like the scammer type to me. Something happened...either good or bad...and he bailed. Simple. The information required the replicate the device is here. Follow through.

The Dragone paper referenced earlier does provide a very interesting glimpse into how a coil and PM can interact to produce significant OU, and could easily explain this device, Magnacoaster, and a host of other devices.

It takes faith to see what others cannot and strength to follow that to reality. Any blind weakling can be a snarking skeptic. It takes a special person to defy them.

Exactly and on top of it, you can see the LED turn off when the rotor has significantly slowed down and the output of the pickup coils falls under the minimal input current for the DC converter to work.

[plengo]

Well,
I think it all got over his head..
I still think from all the communications we had with him
and his history of other youtube projects
with the coil shortening success, etc,
that it was real and no fake.

He might have just fallen for an offer he received.

He told me 2 days ago, that he had at least 2 serious offers
worth of millions of US$...and also that he has his wife on his back and
that she did not want him to release it all for free...

So he probably pulled the plug and
removed his youtube channel now when he accepted an offer from
one of the companies...

Now I am glad he gave me the permission to copy his videos
to my youtube channeel:

http://www.youtube.com/overunitydotcom#g/u

There they still are there.

So I would advise to the members who already ordered the parts to
keep at it and try to replicate it and post as much infos as you can including
videos and scope shots.

Many thanks in advance.

Regards, Stefan.

No problem. I ordered about $500 or more worthy of materials, so I guess I will build it and share the failures or may the successes.

Only one thing was very strange about the second "self-running video" where when he connects the second cable to the positive of the battery, where the other one was already there, and he removes both at the same time and shows the machine running in self-mode without the battery.

One can noticed that the second cable IS connected to the negative of the battery too. At 12 volts 7 amp battery it would easily melt that cable for the 3 seconds he was holding it on his hand. I have to revisit that video again, I could be wrong, but It looked like it was a dead short and not heating or burning his hands.

Fausto.

[hartiberlin]

It was fake all along but I did not want to spoil your excitement. Few would have heard me anyway.

Look again at the first “OU video” (lol!) and by the end of it ask yourself why is the power led (DC-DC converter) still on after he turns the switch off. Huh?!

Look again:
http://www.youtube.com/watch?v=o3YqCp84IOE


Because the 47.000 uF cap is still in parallel with the DC2DC converter !
Man, look again at the video in detail ! I just did it again.

Moreover, why is the same led flashing in sync with the RPM of the rotor when it should be disconnected from stator coils?!!!
Or to put it simpler…What does he switches off then if not the DC converter?!!!
Hint: the other power source? 15V, 1-2A, 2 thin wires… Go figure!

It does not flash at all...
I just watched it again in HD directly from the FLV file on my PC.

The 47.000 uF cap is charged up at 15.07 Volts from all the coil voltage spikes
and when he switches off, only the cap powers still the DC2DC converter for
a while and then the cap discharges and also the LED goes dim and the rotor stops.
That is all what could be seen !

Very normal for such a circuit with 47.000 uF cap charged to 15.07 Volts at the input
of a DC2DC converter and just discharging.

I know, I’m MIB, oil-man, skeptic and a few dozen more…

Before leaving, greetings to the old friends still remembering me. 
See you on the next one, folks!

Probably you did not watch the movie correctly.
I can now see all cables exactly in the HD version and all
is well and no extra cables are seen.

I can recognize every cable which is there.
There are so many cables, cause he needs to bring up the
connections for the lower coils up to the top.
But all is exactly so, as the circuit diagrams have shown.

I think it is really genuine and no fake.

He was just bought out by one of the 2 companies I told you about.
I will reveal their names, if he will not answer my email in a few days.

Regards, Stefan.

[scratchrobot]

No problem. I ordered about $500 or more worthy of materials, so I guess I will build it and share the failures or may the successes.

Only one thing was very strange about the second "self-running video" where when he connects the second cable to the positive of the battery, where the other one was already there, and he removes both at the same time and shows the machine running in self-mode without the battery.

One can noticed that the second cable IS connected to the negative of the battery too. At 12 volts 7 amp battery it would easily melt that cable for the 3 seconds he was holding it on his hand. I have to revisit that video again, I could be wrong, but It looked like it was a dead short and not heating or burning his hands.

Fausto.

Look again.

[Overunityguide]

Best to just ignore people like that at this point...
Anyone with a clue about human nature can see you are an honest builder with only good intentions and real OU.

Told you so, "honest builder" yeah right