Thane Heins Perepiteia.

[CRANKYpants]

Interesting to note that the HV coil also raised in voltage when you shorted the HC coil, that is very counterintuitive, and it would seem to backup the thought that the HV coil is somehow not being induced by the rotor flux because the rotor flux must be diminished by the effect of the HC coil.

Hmmm, it would be very interesting for both of us to do phase tests with oscilloscopes and see if we get the same results what with differing results from HC coils.

I CAN DO THE SILLYSCOPE READINGS NOW THAT I AM HAPPY WITH MY COIL DESIGN FINALLY.

JUST SO YOU DON'T GO OFF ON A TANGENT - THE HV COIL IS SET ON THE CORE - THEN THERE IS ANOTHER LAYER OF CORE MATERIAL AROUND AND ON TOP OF THE HV WINDING - THE HC COIL IS WOUND ON TOP OF THIS SECOND CORE SO IT LOOKS LIKE THIS: (SIDE VIEW)

HC WINDING
SECONDARY FERROMAGNETIC CORE MATERIAL
HV WINDING
PRIMARY CORE
HV WINDING
SECONDARY FERROMAGNETIC CORE MATERIAL
HC WINDING

CHEERS
Thane

But yes we do take lots of cap from you

CRAP DISHING OUT PROPORTIONS HAVE A DIRECT RELATIONSHIP TO LABORATORY STRUGGLES.

I.E.

CDO = LS / OTHER PEOPLE TO BLAME

[CRANKYpants]

Then again as I am currently getting the effect with high current coils can I even be sure that the effect I am getting is the same as Thanes?

ARE YOU USING LAMINATED CORES?

T

[aether22]

I CAN DO THE SILLYSCOPE READINGS NOW THAT I AM HAPPY WITH MY COIL DESIGN FINALLY.

JUST SO YOU DON'T GO OFF ON A TANGENT - THE HV COIL IS SET ON THE CORE - THEN THERE IS ANOTHER LAYER OF CORE MATERIAL AROUND AND ON TOP OF THE HV WINDING - THE HC COIL IS WOUND ON TOP OF THIS SECOND CORE SO IT LOOKS LIKE THIS: (SIDE VIEW)

hmmmm, this does not really remove the concerns of extra core having losses since the HV coil does use an extra core however stealthily hidden.

I think the results make more sense now although that assumes that the flux direction in the outer core is the opposite of the HV coils flux direction, assuming it is backwards then they would tend to reinforce each other, or would they, maybe not, Ok this is confusing.

Still an interesting but more confusing and more difficult to analyze design.

CRAP DISHING OUT PROPORTIONS HAVE A DIRECT RELATIONSHIP TO LABORATORY STRUGGLES.

I.E.

CDO = LS / OTHER PEOPLE TO BLAME

Well then, feel free to offload, kick the dog, and by dog I mean OUmon, he will be so glad to know he is making a positive contribution after all.

You did notice I said 'CAP' not 'CRAP' right?

[CRANKYpants]

FYI Vancouver Gadgeteers Adams Motors 4 sale - 604.739.7717

The Vancouver Gadgeteers club is shipping TODAY, to anybody (except 200V pulsers, those only to tech-types) energy devices that no one else is making available, such as Stanley Meyer toroids, chokes, and inductors.

Gadgeteer Rob Matthies was in the same page in Canadian Business magazine's "intriguing inventions of 2008" and realized that there are similarities between the Perepiteia Generator and the modified Adams magnet motor that the Gadgeteers club is willing to make for anyone (as listed in a classifieds ads.)

If you've wanted to get your hands on a Thane Heins device, consider the Gadgeteers Adams motor and/or the "how it works" DVD.

The club meetings were videotaped from several cameras and even blog-cast. However, the blogcasts were automatically erased by BlogTV after a certain time. Too bad, those were free.

The explanation of the intricacies of an Adams motor and scoping shots were shown in Gadgeteers' meetings.

Several members independently tested the test motors (more than one!) and were amazed to see a resistor go colder than ambient; perhaps similar to the Heins' generator accelerating(?) under load.

We do not claim over-unity. For one thing, the size of our prototypes are too small to be put on a dyno. Also, any test should be adjusted for power factor.

Although the Gadgeteers' Adams motor is not a Steorn device, the power, to touch, seems to be much stronger than the miniscule number of watts drawn, as shown on multiple test meters. You'll also see that we recorded the entire test, including wires getting set up.

By getting your an Adams motor from the Gadgeteers club, you may be able to reverse engineer it, and improve or mass-produce the prototype on a commercial scale.

If you need consulting services, the Vancouver Gadgeteers can offer that, as well.

What we'd like to see: "Anybody Can Make Energy!"

[aether22]

ARE YOU USING LAMINATED CORES?

T

I an using the original MOT cores so yes, but they have steel pieces at the face which I attached previously and I have been reluctant to remove them mainly because I fear the effect will become crap as it is with my cut down core version.

I would note that many/most of your MOT cores have solid steel somewhere such as your back iron. (which may vaguely resemble but isn't the same thing as a transformer lamination)