Stanley Meyer Explained

[h20power]

so that's a no then... your car isn't converted to run on water as its sole source of fuel.

i find that interesting.

I find it even more interesting that you don't want the technology, you haven't read the thread I posted, you haven't done anything, all you want is for someone to do song and dace for you. News flash I am not an entertainer so don't you dare go expecting me to do a song and dance for you.

So using your type of mindset shown here, you reject the technology and everything else I have tried to give you, and again I find that even more interesting.

h2opower

[HeairBear]

So, how does the circuit diagram for the variable plate demo cell play into with what you are talking about? The diagram shown is an edit of the original but labeled with substitutes. Why did you choose 2 henry coils when the original coil wasn't even in the same ballpark?

Here is a pic of the actual device diagrammed...

[h20power]

Hi HeairBear,
That is just to get people started as the circuit will work and the inventive mind can make it work even better.

What has it been now since we've last talked, 1-2 years? How have you been?

Well, after Aaron and his crew threw me out of the Energetic forum I was free to think without all of their misdirections and distractions, and now I think I have solved the whole thing.
Things I know for sure:
How the hydrogen fracturing process fully works
How Stanley Meyer's technology breaks down the water molecules, plus get this, it is not a, "Catastrophic Dielectric Failure."
How the Electron Extraction Circuit works fully
How the Gas Processor works fully
I know where the energy is coming from to run a car plus all of the rest of the things Meyer talked about doing with the technology.

I am finishing up my understanding of the VIC Matrix Circuit right now, just have a few more experiments to run and a whole lot of math to do.

That 8XA circuit, if one thinks creatively, can power a car but they will need to build the Gas Processor as one need that device to be able to prolong the formation of the water molecules as Stanley Meyer explains.

I posted quite a bit of information on the http://www.hereticalbuilders.com/showthread.php?t=174 site that is, for the most part, based in science.

Enjoy!

h2opower

[h20power]

Hi TIA,

That circuit design I got from Tony Woodside and is the circuit that is being used in the video I post by OutlawStC. http://www.youtube.com/watch?v=VziZ33MA7OM. Now OutlawStC doesn't fully understand what is going on but I do. The one thing everyone needs to learn about Stanley A. Meyer water for fuel technology is Lindemann had it all wrong in his explanation of Meyer's work for there is no Catastrophic Dielectric Failure taking place. Meyer's technology doesn't work like that it works by stealing electrons from the molecules which makes them unstable and break apart for they no longer can obey the conservation of mass. I go over it a bit here: http://www.hereticalbuilders.com/showpost.php?p=4588&postcount=74

Remember that circuit is just to get people started for it is working, I am finishing up my work on the VIC Matrix Circuit and when done will share what I have learned about it, but so far that transformer is very difficult to explain. I do go over how to get it working correctly loosely at the other site but have to break it down for people as that is a lot of information one has to take in and learn how to do with lots of math to boot. I just need to confirm the science and math with expire-mental data, okay?  Once I have all the answers I will post it on the other site.

Tony Woodside posted an updated circuit here: http://www.globalkast.com/projects.htm

Thanks
h2opower

Hi H2Opower

Nice Circuit, but I have one little problem, and you may have already corrected it on newer designs, but there is so much out there that I rarely have time to view half of it.

The "Pass" component shown is an SCR, which once conducting will not shut off until the current drops below the threshold point.  Is this the correct part and idea?  My only assumption is the actual current flowing through the coil and "Water Cap" is always below the this point, but wouldn't this make start-up a "Problem".    (As in, the first cycle would turn on the device, but until the "Charge" was enough to limit the current, the part latches.)

I realize that there may be dynamics I am unaware of and I have not actually built this specific circuit, but I have made enough of this type of setup to know that reducing the current has always been one of the hardest parts (For me, at least...) and I am quite curious.  I can imagine that a 2 Henry "Choke" might be enough to prevent "Latch-up", but I didn't want to guess and I don't have enough experience with the dynamics of the "Water Cap" itself to figure it with plain math.

I am going to read and save the last few links you provided, and that may very well answer my questions, but any insight you would care to offer would be greatly appreciated.

TIA

[h20power]

Hi Art,
Sorry about that, guess I am not up on all the latest shorthands. The VIC Matrix Circuit is one complex device that looks so simple. Try this, go over one full pulse and one full off time and write down everything that takes place with respect to time, and you will find it is far more complicated than it looks. Then with each new type of transformer something totally different was added in to the mix. A long time ago I solved one part of the figure 6-1 VIC in the SMTB but there is a lot more I missed and some things I got dead wrong. One thing about me is I am not afraid to admit if I have made mistake, but like most I don't like it when it happens for I have to rewrite my mind in a way and change my thinking. Getting over Lindemann's explanation was about the best thing I could have done for it opened up a whole new line of questioning and this time all the answer, so far, are coming from today's modern science. Now I can see that everything Meyer did can be explained with science. Thanks for kind words, and I hope I don't let you down.

h2opower