Howard Johnson Replication Tube Claim

[chrisC]

Don't remember anybody catching this but is a report from an replicator from 2003 that constructed
HJ's rotary motor and reported operation for three days after which the magnets depleted.  Seems to
jive with Al Witherspoons story that HJ had trouble sourcing accurate magnets to his spec.  Would also seem to somewhat vindicate Mylows efforts as it seems irrational anyone would hoax a depleting stator magnet!

http://www.freeenergynews.com/Directory/Howard_Johnson_Motor/Blueprints/hard_replicate/index.html

I can believe Mylow's report of depleting stator magnet.

A few days ago I bought an Alnico U shaped stator magnet from Ace Hardware, I think the pull strength was quoted something like 15 lbs. Then I got started putting a variation of MyLow's set-up using neo's (rotor) super-glued to an aluminum flywheel about 9 inches wide (I did not have the channel shaped rotor magnets) resting on a low friction Ricoh scanner bearing . After a few hours of playing with trying to get the wheel turning, I noticed that U shaped stator's pull strength dramatically decreased! It was never like when it was first taken off it's keeper.

This can be easily verified and that's why you'll see reports of depleting magnetic strength and hence the slow-down seen in Mylow's last video.

cheers
chrisC

[plengo]

I am crying very hard. Not only this is lacking lots of evidences we are also being blamed for being skeptical because of that lack of evidence and the  very hard to believe stories that Mylow told us.

On top of that, the reporter that support our community is selling the plans that no one is able to replicate. What is happening to our community?

Is not this place a place where science and experimentation is supposed to be accepted? Is this Disney World now?

Until Mylow or anyone come up with replicationS that works and are accessible by members or individuals with honorable knowledge all is just reliable as evidence.

Should I accept every single video in youtube as undisputable good evidence to the free energy world?  Should I not first eliminate all doubts before waisting my time for experimentation? Should we not first dissect the so told evidences to the minimum logical and reasonable parts?

For those that wants to experiments, please do it. It is good that but remember only to not claim victory before the fight is over. I am one for that. Let's experiment, even Mylow replication but dont say it is a working device before enough evidence is really given.

Fausto.

[pinestone]

Did anyone see the iron filings video Mylow made?

The 'wave' of filings have the same pattern as the lowest magnetic potential as seen through one of my flux resonator lenses.
This video shows the flux at a 90 degree difference between two rotor magnets and a stator magnet.

http://www.youtube.com/watch?v=Y8sIAFSq79U&feature=channel_page

Maybe this 'longitudinal' wave obtains some sort of resonance within the domains of the iron. A heat transfer between the domains combined with a phase shift could result in some additional energy. Like an 'in-phase' inductive kick.
Not really violating COE if the stator magnet loses its magnetization over time.

[LightRider]

Nice work.  I like data.  I posted it at http://peswiki.com/index.php/OS:MYLOW:Data

Thanks,

Analysis of Mylow video #7 (http://www.youtube.com/watch?v=R7PZ18uTPCg)
Note # 1 moving video camera.
Note # 2 the movie have 1612 frames (1 frames = aprox. 0.04s)
Note # 3 Frames 0 to 641 not usable
Note # 4 Frames 642 to 966 the rotor make 4 full revolutions : 1 rev. in 67 frames, 2 rev. in 70 frames, 3 rev. in 73 frames and 4 rev. in 80 frames. **So each round takes longer (deceleration).
Note # 5 Frames 967 to 1335 Mylow turn around and show his bed for aprox.368 frames. not usable.
Note # 6 Frames 1336 to 1472 the rotor make 2 full revolutions : 1 rev. in 66 frames and 2 rev. in 70 frames.**So each round takes longer (deceleration).
Note # 7 While the camera caught the bed, the revolutions of the engine accelerated.
Thanks,

[nyctuber]

I can believe Mylow's report of depleting stator magnet.

A few days ago I bought an Alnico U shaped stator magnet from Ace Hardware, I think the pull strength was quoted something like 15 lbs. Then I got started putting a variation of MyLow's set-up using neo's (rotor) super-glued to an aluminum flywheel about 9 inches wide (I did not have the channel shaped rotor magnets) resting on a low friction Ricoh scanner bearing . After a few hours of playing with trying to get the wheel turning, I noticed that U shaped stator's pull strength dramatically decreased! It was never like when it was first taken off it's keeper.

This can be easily verified and that's why you'll see reports of depleting magnetic strength and hence the slow-down seen in Mylow's last video.

cheers
chrisC

When I was searching the web for horseshoes, one of the first sites I came across specifically warns about using horseshoes for repelling, as this drains them. I assumed this was common knowledge but maybe not? Dunno. Thanks for the post.