Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Steven Marks Tube Power Supply

Started by wattsup, March 31, 2009, 01:38:50 AM

Previous topic - Next topic

0 Members and 2 Guests are viewing this topic.

Print
Go Down Pages 1 2 3 4 5 ... 15
User actions

wings

#10
March 31, 2009, 08:53:44 AM
Quote from: otto on March 31, 2009, 07:56:05 AM
Hello all,

@wattsup

thanks.

I can only say that Im happy to share my work because maybe, just maybe, someone of you will have success. As posted before, I dont have the needed transformer and about caps with low ESR I can only dream!!!

So, people, use my informations and finally start to work.

Showing you my problems I ONLY wanted to say that if you wait for me to do the job it will take a time until I have solved this problems.

Otto

low esr in flash camera

Bruce_TPU

#11
March 31, 2009, 08:57:15 AM
The tube amp starts a chain reaction (catalyst)

The secret is what is taking place in the collectors. 

A tube AMP is needed for each frequency.  When unit is switched over to all SS, the SS is made to mimic the frequency reproduction of a tube AMP.

Without a tube AMP, actually three of them, you will never see catalyst, even with the right circuit potential and litz, which no one here gets yet, because they won't look at the frequency's journey inside of the loop collector.

Oh, P.S.  The secret is not found in HV either.  It is found in HOW DIFFERENT frequency's react with one another.  Nothing that can't be found with some good research. And then how they react traveling, opposing one another.  You can start with GK's Heterodyne thread, CTG Labs transformer experiment, and then go to my thread discussing lightning and then move on the circuit potential, while at the same time, re reading and studying everything SM said!  LOL
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

gyulasun

#12
March 31, 2009, 09:06:51 AM
Quote from: otto on March 31, 2009, 02:07:43 AM

... into a 100 microfarad or so electrolytic cap with low ESR (??) and another 0,01 in paralel,


Hi Otto,

If you question marked the ESR what it may be, then it is the short form of Equivalent Series Resistance of  (mainly)  electrolytic capacitors. It simply means how lossy they are, low ESR means much less loss i.e. heat would develop inside the body of the capacitor.  On the other hand, with low ESR a capacitor can supply higher peak load current than a normal because the lower inner resistance (which is also frequency dependent) is less of the limiting factor.

Electrolytic capacitors with low ESR values normally cost higher than 'normal' electrolytic caps of otherwise same ratings.

There are off-the-shelf  ESR tester instruments, here is a home-made-able practical circuit if anyone is more interested: http://members.shaw.ca/swstuff/esrmeter.html

rgds, Gyula

EDIT  I noticed wattsup mentioned in the meantime what ESR is, ok.

Grumpy

#13
March 31, 2009, 09:32:16 AM
Quote from: otto on March 31, 2009, 06:58:37 AM
Hello all,

yes, Im also thinking how SM made this with SS but I have first to see the magic with my tubes so I can really understand how and why.

Now, lets think what we know:

the TPU output has sinewaves with kicks on top of them.

This means we need kicks and sine waves in our TPUs. The kicks are made in our well known manner with MOSFETs.
Now the sines: when I connect 1 end of my high voltage to the copper core then I have the needed sine waves and depending on the frequencies used I have the needed TPU output but still no "magic" to say so.

As always Im in a big trouble. My heating transformer has a 6,3V heating and the 5U4 needs only 5V. The next is that we MAYBE need 500V - 0 - 500V as the plate voltage and my transformer delivers me only 300V - 0 - 300V.

Any ideas? Dont say that I should surch in junkyards because this is impossible.

A hand made transformer? Yeeeees, but money, money, money.....ha,ha.

Otto


How do you think the TPU works?  What is the basic mechanism that makes it work?

It is the men of insight and the men of unobstructed vision of every generation who are able to lead us through the quagmire of a in-a-rut thinking. It is the men of imagination who are able to see relationships which escape the casual observer. It remains for the men of intuition to seek answers while others avoid even the question.
                                                                                                                                    -Frank Edwards

Grumpy

#14
March 31, 2009, 09:36:57 AM
Quote from: Bruce_TPU on March 31, 2009, 08:57:15 AM
...

The secret is what is taking place in the collectors. 

...

Oh, P.S.  The secret is not found in HV either.  It is found in HOW DIFFERENT frequency's react with one another. 

...


The "collector" is just a piece of wire shorted by a resistance.

The secret is the effect that HV has on the aether. 
It is the men of insight and the men of unobstructed vision of every generation who are able to lead us through the quagmire of a in-a-rut thinking. It is the men of imagination who are able to see relationships which escape the casual observer. It remains for the men of intuition to seek answers while others avoid even the question.
                                                                                                                                    -Frank Edwards
Print
Go Up Pages 1 2 3 4 5 ... 15
User actions