Are Tommey Reed´s pulse motor circuits overunity ?

[bearicey]

"Transverter systems may be the Volskwagen of OU systems for the money-"handicapped" research guy!"


http://peswiki.com/index.php/OS:Transverter

[powercat]

Hi everyone,

here is a video I made of a replication of Tommey Reed's circuit.

http://www.youtube.com/watch?v=W4fYvSRxHd0

No Over Unity for me.

I challenge Tommey to do the capacitor test as I have done.


Luc

Hi Luc
great video and great timing, hopefully Tommey will take up your challenge
looks like he was questioning the type of coil your using

Quote from Tommey
Is your coil, is it .61 ohm 16gage wire?
This is a basic coil out of a microwave oven at 120v ac

cat

[allcanadian]

I think Mr.Reed is exactly right, a replication is just that---- a replication of the experiment. To use completely different components,voltages or values of components is "NOT" a replication in any sense of the word. As well Mr.Reed utilizes an air core coil, which I noticed is the primary from a microwave transformer, the qualities of this coil are far removed from the iron core others have used. This is the biggest problem I see here in the forum, people throw some random components together and call it a replication, which it is most certainly not, then state their replication has failed. I would submit "they" have failed due to a lack of understanding, like the old saying goes---- "don't blame the messenger". In any case Mr.Reed's circuit is based on technology Nicola Tesla perfected over 100 years ago, this is nothing new in any way, it has just been ignored by the masses for a very long time.
Regards
AC

[gotoluc]

Hi everyone,

For those who did not read Stefan's questions he posted on my YouTube video they are in bold below with my replies.

Hi Luc,
did you try to get the driver frequency tuned to the resonance frequency of the coil ?
Is it really this low at 1.23 Khz ?

Is this the resonance frequency ?
Maybe you can tune to a better harmonic frequency of the resonance frequency ?
Maybe you can retry your tests without the iron core and tune to the frequency of your driver to the resonance frequency of the coil ?
Maybe the iron core is too lossy.

My reply:
Hi Stefan,
thanks for looking and posting your positive comment.

I did do many sweeps of up to 200Khz (555 frequency limit) on all kinds of coils, air core coils and with cores. Out of the 10 or so coils tested this is the one that gave most voltage output at this low frequency with minimum amp input.

I would need AC to achieve Resonance. Never been able to do it with just chopped DC. I was also trying to keep it to what Tommey Reed has been doing.

Stefan:
Hmm,
you should be able to get resonance also with chopped DC.
The coil does not care about a DC level being superimposed, at least if you use a coil WITHOUT an iron core..

What best frequency do you get, if you unplug the iron core from this coil you have shown ?

My reply:
I've never been able to do it, so pleas show me a video of someone that shows resonance using chopped DC. When my coils go into resonance using just 10 volt AC the coils output is well over 150 volts rms

I pulled out the core from the coil and it now performs best around 12Khz.

[gotoluc]

Hi Luc
great video and great timing, hopefully Tommey will take up your challenge
looks like he was questioning the type of coil your using

Quote from Tommey
Is your coil, is it .61 ohm 16gage wire?
This is a basic coil out of a microwave oven at 120v ac

cat

Hi cat,

I did see that post but did not realize it was a question for me.

The coil I used in the video is not from a Microwave Oven Transformer. As I replied to Stefan on YouTube I did many tests using many coils including an AIR CORE MOT primary and also a steel core MOT primary. Out of all the more then 10 coils I tested I chose the one in the video as it performed the best results.

I hope that can answer some questions.

Luc