Selfrunning Free Energy devices up to 5 KW from Tariel Kapanadze

[elementSix]

I got HOT news....that needs to be confirmed.... but is a good tip....
Nilson Barbosa use to sell and fix WELDING MACHINES in his hometown.

In 2 or 3 of TK's Videos there is a Yellow welder on the floor.  The GB video its in the garage and in the 2004 video its in the living room..

[NickZ]

  Maybe TK used to be a welder, also.

[elementSix]

Who ever that was who posted the Hendershot video links, thanks a lot.  I found the original english video that is 2 and a half hours long and shows you exactly how to make the Hendershot Generator.  Heres the link.

http://www.youtube.com/watch?v=HsKdgLIVnu8

Here is the link to parts list and tools and circuit diagram.

http://www.mediafire.com/download/9yvn66e78n9bf9k/HendershotGenerator.rar

This link is just various generators, not sure why this is linked on the youtube page...
http://www.mediafire.com/download/dz6epheuhcvfe2s/generators.rar

[Gidfactor]

Thanks very much element six ....

It was me anyway...

Thanks will follow..

Cheers...

[stivep]

Hi T-1000 and Wesley,

This for Wesley since i had Barinum titanite which i puchased 2 years ago from ebay.
I proceed to conduct the experiment as shown in the rexresearch as shown below but without the Barium ferrite magnet.To prove if their OU experiment is valid.There is OU indeed the signal is amplified only at the resonance frequency or it's harmonics.Not only it's voltage is amplified it's current as well.But it's below ~0.5mA shorted output from another bilfilar winding for less than 1uA input.I able to light led from with less than ~1uA at input bifilar winding .
If i bypassed the barium titanite the current input to coil bilfilar input is 40mA and the Led was not lit from bilfilar output winding.


This is how i setup my experiment merely using existing 40 turns of bilfilar 18AWG on 3" toroid this is borrowed from my HHO experiment.
The inductance reading for bilfilar is 24.88mH for both winding.I did not follow 150 turns as describe in site.

As describe in rexresearch to use sine wave to use is from 20KHZ ...40KHZ.
Since i had 5 pieces of Barium titnate as attached.I proceed to use croc lead one beneath the Barium chunk and one lead over the chunk and this lead to Bifilar input.
I started with multimeter A/C setting i observed if input voltage is 0.5V A/C the output from another bilfilar winding (isolated from frequency generator)is 3.7Volts A/C for one particular sample.

If you take a look at the photo i noticed a particular chunk is different  colour from the rest as delivered to me 2 years back.The piece which at the bottom of the photo was able to resonate at 16.8KHZ for my case and gave the highest output(similar colour to white clay).The rest is between 20KHZ to 35khz(dark grey samples) .By the way i get higher reading in multimeter in 1 decimal place if i use square wave instead of sine wave.

The scope showed a amplified waveform at the output if i connect lead via Barinum but if i merely connect directly to bifilar the amplitude is the same with usual phase shift if compared with input.
Maybe with Barium magnet in hand  maybe i can program my <20mA microprocessor to output at 16.8KHZ sq wave to resonate the Barium titnate to create a loop back to allow it to self run.

For everyone else-
This experiment is a big eye opener for me.It's hard for me to prove unless 1 or more people carried out this easy experiment.There is ou in miliwatt level enough to light led from below 1uA input
But the most important requirement is a frequency generator beside multimeter and optional scope which allow you see the amplified waveform to your heart content.


{

To T-1000 can you recall the previous discussion we recently had in this forum about Resonance Amplifer which is proven around 6watt of overunity using a basic setup using Barium-Ferrite Magnet base on one of the site i have provided link.http://www.rexresearch.com/mra/1mra.htm#intro

I have finally found a link on where to purchase this magnet from quantity as low as 1, 200 or 1000 or 2000 depend on company.All the magnet Companies in one site is listed below.
I merely know in business sense China is the world's Main producer for neodymium magnet ,Lithium and etc.

Some companies accept wider range of payment terms :T/T, D/P, Paypal, Western Union

You might laugh if i told you the cost of magnet is $0.01 ..$0.5 ea

http://www.made-in-china.com/products-search/hot-china-products/Barium_Magnet.html

thanks my friend I'm on the go so just quick Thank you(I'm  driving, not going to trouble with authorities )
Very interesting.








http://www.youtube.com/watch?v=QucsK2hg0eo




Wesley