Selfrunning Free Energy devices up to 5 KW from Tariel Kapanadze

[TEKTRON]

I have a couple of questions. Who's build is this from? Are the caps wired into the bifi circuit or just laying on or otherwise propped up by the core half?
DL from FreeEnergyLT

[verpies]

@grizli

Oh well, I suppose you are right - it does not matter if we call this a ferroresonant effect at this point. It's better not to call it anything, in order to avoid hasty conclusions.

What's important is that the measurement is made with the 50turn Longitudinal Coil as INPUT and the Transverse Coil as OUTPUT.

However the instructions at http://freeenergylt.narod2.ru/aidas/ state that the measurement should be made with the Transverse Coil ("copper plates") as INPUT.

1. Connect 51 turns coil to Vector Network Analyzer output / Spectrum Analyzer input.
2. Connect cooper plates half-ring winding to generator with white noise output.

In other words, the output of a signal generator is connected to the input of the Transverse Coil, and the "scoping" is done on the 51 turn Longitudinal Coil.

Re:  http://www.overunity.com/index.php?topic=7679.msg304739#msg304739

[pix]

All,
I am quite confident that you will not have a detailed plan and decent explanation why it works and what-to-do.
Otherwise you would have this already.
All the information we see on this forum regarding recent succesfull replication is provided in a very haotic and unprofessional manner.
Instead of clear explanation: "guys, this is how it works, the source of excess energ is ....., please see detailed schematic with pictures and do replication this way:... ect." - what we have?
Pieces and bits of info here and there,lot of videos, lot of "educate-youself-links".People claiming that they have an answer and working device -instead of giving full explanation, engage in discussions with individuals.
Target is slowly "dissolving".
Information instead to be placed in one piece, is smeared through dozens of pages and replies.
I don't understand this.

Stivep, Zilano, T-1000
Please if you are willing to share, and you have a working  unit- try to condense and detail all necessary information in one document.
Not everyone on this forum have your level of expertise and such fancy testing equipment in large amounts.
People have limited resources to fail with their replications,just because information given is incomplete.For example,recently a lot of people was asking how do you phase lock two Vellemanns function generators.

How do you want to "improve the world and give energy indenpendency to the people" in a such messy and chaotic way?
Regards,
Pix

[verpies]

Instead of clear explanation: "Guys, this is how it works, the source of the excess energy is..., please see detailed schematic with pictures and do replication this way:... etc." - what do we have?

I'd like to note that it is possible to have a working device without an understanding of how it works and what phenomena are behind it.
I think only the info in bold font is necessary for replication.

We can analyze/theorize about the "hows" and "sources" after the device is replicated and functioning as described.

[wattsup]

@grizli
However the instructions at http://freeenergylt.narod2.ru/aidas/ state that the measurement should be made with the Transverse Coil ("copper plates") as INPUT.

In other words, the output of a signal generator is connected to the input to the Transverse Coil, and the "scoping" is done on the 51 turn Longitudinal Coil.

Re:  http://www.overunity.com/index.php?topic=7679.msg304739#msg304739

Yep.

@All

Got the Yoke done so testing can start tomorrow.

I did the above. Resonance is ONLY at 24-26Mz. I will do all the variables and figure out my target frequencies but in general we are talking mucho Mz.

wattsup