Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



STEORN DEMO LIVE & STREAM in Dublin, December 15th, 10 AM

Started by PaulLowrance, December 04, 2009, 09:13:07 AM

Previous topic - Next topic

0 Members and 65 Guests are viewing this topic.

Print
Go Down Pages 1 ... 199 200 201 202 203 ... 801
User actions

PaulLowrance

#1000
January 02, 2010, 12:21:14 PM
The flip-flop circuit tests out great. It's not connected to the eOrbo yet, just a manual run. It's a d-flip-flop. The starting trigger goes to the d-flip-flop clock pin, and the ending trigger goes to the d-flip-flop clear pin. That way the timing can never get out of sync. Schmitt triggers are used between the triggers and d-flip-flop. The Q pin will go to the mosfet, which will go to the coils.

Also I might use LEDs & photodiodes instead of pickup coils.

Bruce_TPU

#1001
January 02, 2010, 12:27:03 PM
Hello ALL,

My Steorn Magnet Motor is complete, and I am just now working on my electronics.  I can't wait to have this thing up and running so that I can begin to experiment!

Cheers,

Bruce
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

Omnibus

#1002
January 02, 2010, 12:42:21 PM
Did you read this:

QuoteWe will be placing a system in the Waterways and will allow people to bring their own test equipment (or use ours) - and you can test a system the way you see fit. Note that all tests like this will be done under the supervision of one of engineers - this is simply to prevent someone who might want to break a system apart. However no reasonable request will be refused.

Sean
Off to Dublin, everybody ...

This happens for the first time in our community, someone to invite people to do tests as they please on his machine. I'm out of words. That's exactly how people claiming OU should behave. Go Steorn. All power to you.

samedsoft

#1003
January 02, 2010, 01:00:50 PM
Quote from: Groundloop on January 02, 2010, 10:58:48 AM
@samedsoft,

Back electromagnetic force is what happen in any coil when you add current to a coil.
The coil try to resist the current change. An inductive kick back voltage is what you
get from a coil when you switch off the current in a coil. Don't mix those two.

As to you questions, I'm not quite sure what you are asking?

Alex.

Dear Alex,

   I meant the BEMF due to loading on the secondary side of the transformer. On a regular transformer, loading on secondary increases primary current.

   I thought your system did not increase primary current.. I was thinking orbo..

  You know when Ossie loads his orbo it does not consume much current on the primary.. But he looses rpm.

  In a similar sense, loading on orbo trafo secondary may cause a lag on primary current maybe?

  Rather than resistor using an inductor would make latency on middle transfer system. Latency would cause consuming reactive power and conversion of reactive power to active power.... as Thane's Bi-Toroid Transformer..

  Could you please post a video in this topic?

  Thanks...
   

Groundloop

#1004
January 02, 2010, 01:06:15 PM
@Bruce_TPU,

Great work. If you put your toroids flat against you rotor the you get only one
attraction point instead of two. My I recommend you put your toroids horisontal
with the toroid hole pointing upwards.

Alex.
Print
Go Up Pages 1 ... 199 200 201 202 203 ... 801
User actions