STEORN DEMO LIVE & STREAM in Dublin, December 15th, 10 AM

[PaulLowrance]

Since I'm getting back to the "tiny orbo replication" today, I'll be blogging about the results here -->

http://globalfreeenergy.info/tag/tiny-orbo-replication/

Blog comments are now open, but please no trashing. Thanks.

[EDIT: corrected URL]

[captainpecan]

Damn, I logged on and saw a bunch of posts, and was excited to see how much everyone has learned and moved forward.  Instead I got to just see a butt load of bickering.  Paul, you have got to chill the hell out.  This is just getting really STUPID!!!!  Ossie simply posted some interesting results that everyone in this thread thought were fantastic and show promise, but you have laughed at him because he did not measure COP yet.  Here's your qoute...

People should be encouraged to take COP measurements. How long something runs on a battery is meaningless, lol.

WE DON'T CARE!!!!  WE ARE TRYING TO WORK HERE!  Although I agree just like pretty much everyone in here, that COP measurements are scientific proof and very much needed if one is to get scientist backing.  But I'll be honest, I want a self runner, and do not give a crap if scientists back it, and I'm pretty sure Ossie feels the same way although I will not speak for him.  A self runner cannot be disputed. One that the battery dies on, causes tons of arguments over how the COP was measured and pissing matches, that ultimately still lead to a device that runs until it stops.

Please get back on track Paul.  I mean no disrespect, but please stop getting irritated if someone gets results that do not fit your bill exactly.  I'm just curious though, why is it that you do not want a self runner also?  I thought we were all after the same thing here.

[woopy]

Hi all

back home  and slowly open the lab door       and  the machine spins  (since 18 hours)  at 197 rpm  battery (which is a non rechargeable AA and not AAA as i mentionned earlier) at voltage 1.22 volt  and accu flicking at 130 to 140mv

by looking attentively i heard some time the rpm going down so i stay to see what is going on. The machine seams to "respire"  it goes down and than after some minutes it goes up again. Once it goes down to 111 rpm and get back to 194 rpm 5 minutes later

Than something weird happen . I tried to measure the voltage of the accu and stayed sometimes with the voltmeter probes on the accu. than it decharges very fast to 50 mv and the machine stops. ??

Do a voltmeter take out the current when measuring  ??

Anyway i will try now with a rechargeable AA battery without depleted accu

and see what happens

regards

Laurent

[captainpecan]

Good work, thanks for sharing the results.  You have at least shown that it is still very efficient, and still somewhat backs up Ossie's results.  I'm with you though on that one, using a rechargeable is much better experimentally.  I'm glad your choosing to remove the other dead batteries just see how this thing goes.  It would not be a bad idea however to just add a small pickup coil and harvest a bit of that rotors kinetic energy.

[woopy]

Hi Captain
thanks for supporting this OSSbo idea

what i can not target  is why i don't get the same scope trace across the coils.  Ossies shows us a regular oscillating trace Plus on the top a little square spique. On my replication i get what is on the picture on my previous post  that is   a straight  up curve than going smoothly down than almost flat than back to zero than  ( i suppose must be the) kickback power     = a straight down  and up square trace  ??

I jusat try a new rotor with alternating polarities  NSNS etc   but the trace is always the same and the timing with the reed switch is much more difficult to tune and the rpm stay very low.

HEHE not so easy the quest to OU

but lets go on with courage and determination



Hello Ossie  some result or video  ?


good night


Laurent