Pulsed DC Transformer with Embedded Magnets

[ltseung888]

The essential pendulum calculations

These diagrams are reproduced here so that the participant does not need to read the few hundred posts in the Lee-Tseung Lead out theory thread.

The key concept is that horizontally applied work or energy can lead out vertical work done by gravity.  Approximately 1 part of vertical gravitational energy can be led out by 2 parts of supplied horizontal energy.

[ltseung888]

Meeting with Jim Nichoson of Gravitycontrol.org on April 17, 2010

Jim was from Canada but lived in Hong Kong for over twenty years.  He emailed me and would like to see the Tong Wheel and FLEET on his brief trip back to Hong Kong.

Jim: “I read your information on the Internet.  I have a friend working on the Don Smith type device.  He is not successful yet.  Do you have a Tong Wheel and a FLEET experiment here to show me?”

Tseung: “Yes.  You can film the Tong Wheel and you can also do the FLEET experiment â€" vary the frequency to pulse a LCR resonant circuit and check the peak-to-peak voltage waveform.”

Jim spent two hours doing the experiments and filming the Tong Wheel.  Others including Jeff, Forever and Debbie were present.
   
Jim: “I understand the construction of the Tong Wheel now.  There  could not be any hidden energy source other than the 12V battery.  The theory is from the pulled pendulum.  Have you got any marketable products yet?”

Tseung: “You can buy a Tong Wheel for HKD150,000.  However, you have now performed the FLEET experiment.  You will go for the cheap alternative.”

Jim: “I was willing to pay HKD150,000 for the Tong Wheel.  But the FLEET is so much better and cheaper.  I never expected  a simple pulsing from a RMB600 Pulse Generator on a LCR resonant circuit can conclusively demonstrate resonance behavior.   I wonder why my friend failed?”

Jeff: “Getting  resonance is not easy.  We failed with the first Joule Thief we tried.  You can have one of the failed models.”

Jim: “You used a different one thousand ohm resistor as compared with the one shown on the youtube video.  You also soldered in extra unnecessary wires.”

Tseung: “That is why I do not always trust the replicator reports on the Internet.  It does not surprise me that your friend failed to replicate the Don Smith device.  Ask him to do the basic FLEET experiments first.”

Jim: “Why are you giving such information out freely?  A successful commercial product can worth billions.  That is one of the reason I had to come and see the Tong Wheel and the FLEET myself.”

Tseung: “Are you aware that some inventors such as Stan Meyer got poisoned?  You are now another murder target.  My reasoning is that if there are thousands or millions of people knowing the technology, there will be no point in murdering the inventors.  I shall be safe.”

[NerzhDishual]

Hello Sandy,

I left this thread alone for a couple of days (I really mean 2) and ...
What a surprise !
You again on overunity dot com...
Nice to see you here.

Your mojo piece is just great and  marketable, IMHO.
Do you sell any CD?

BTW: It 'sounds' like this piece actually gave me some Mojo...

I made a lot of others experiments with a couple of JT. Hence my silent.
I added another toroidal coil and was able to charge a bat and add another led.
The CCT (CCT is an abbreviation for Circuit. an abbreviation
is very usefull when you do not want to write too much letters).
Private joke.

Guess what?  these JT CCTs do not seem to care being charged....
My amp consumption is about 12 ma.
Yes, it could be possible to charge 2 batteries.

I'm now figuring out that all I have to do is to try different things.

Very Best et à pluche.

[pese]

@ ND

This circuit , shown that
It is a  wrong way.
You will find out that
it was only shown,
that an second  battery can be load.

Pls try to connect
-instead the second battery
(chargeable battery= accu)
the  " output-power" -instead-
to charge the first (driving)  battery- at same time- (!)
 
(You save - the work-  to swap both batteries ,
the "charged" against the "unload")

At Last:
This is the ONLY "working" test that can shown
you the true , so you it is un-need to look for more
mesurements and tests
that cant help to understand .

Gustav Pese

[nul-points]

hey Nerzh!

that's a cool development - a JT with a 'couple' of coils!

and it sounds like you've tested it already and found you can charge a battery and light an LED of the second coil's secondary?

(er - so is that a secondary-squared?!?!)

are there any advantages to having two toroids from one Tr?


glad you liked the mojo track - we had a gig in deepest Dorset Friday night and the Maitre d' specially asked us to include that one during the evening

the highlight of the evening was when we announced that the airports had re-opened and we played a 'punky' version of Peter, Paul & Mary's 'leaving on a jetplane'


anyway, i digress - back to Pulsed DC transformers with embedded magnets...

i certainly found that adding a Neo to one of the toroids on a multi-toroid Xfr i'd made caused an increase in flyback voltage - unfortunately, it also seemed to cause an increase in input current

have you tried experimenting with Neos on your JT ccts?

(cct is an abbrvn. for circuit so you dnt hv to... oh, you've done that one!)

i'll be interested to see if this thread 'leads out' some real result data about pulsed DC transformers with embedded magnets

all the best
sandy