PLEASE READ THIS-MAJOR BREAK THRU FROM BILL MEHESS

[Paul-R]

5.  Let's take roughly 1 kW to run a house (a low estimate I believe) --

The figure often quoted is 2.5 Kw.

[billmehess]

I spent about 12 hours in my shop adding my upgrades here are this morning results, I will be running tests all day long and over the weekend to see if these hold up

First I am using just 3 modules and a 60,000 uf cap.

Time         Start voltage        end voltage         Cap voltage

8:30 am     2.106 volts             2.256 volts          .562 volts
9:00 am      2.115                    2.256                  .563
9.15 am      2.136                     2.261                  .573
9.45am       2.199                    2.285                   .555
10 am         2.202                     2.290                  .540
10:15 am    2.195                    2.276                   .539
10:30am     2.213                    2.285                    .538

The ending voltage is the voltage after 15 minutes when I disconnect the cap. I short out the cap during that time to restart from  a 0.00 reading of the cap.
The test is now done for 60 seconds not 1 hr or 3600 sec.

The device has always showed a increase in voltage even after running the load.
using  E= 1/2 cv (squared) and dividing by 60 sec. wattage is now .145 watts 
Also these three are now running in series. Adding modules in parallel will increase the wattage.
It's a mystery.
Bill       

[WilbyInebriated]

  WillyInebriated -- you quoted me out of context.  I was seconding a commendable suggestion made by e2matrix,
  This is not a "childish" idea, but a commendable one.

i didn't quote you out of context... nor did i suggest it was a childish idea. don't be asinine. i said bill has a plan, which he has already explained. stop behaving like an impetuous child by repeatedly pestering him to modify his plan to suit your impatience and repeatedly pestering him for further info. perhaps you should try some of that rigor without rancor you talk about... starting with rigor instead of this assumption followed by speculation, resulting in inevitable conjecture... sounds like a plan? what do you think?

[ramset]

HHMMMM

Bill
Looks like you just whacked a few hundred Million bucks [at least]  off the Cost per Watt?

Steve
"W" sounds Cranky? I guess he didn't catch any fish yesterday??
So Now he's fishin for Jouleseekers?

Don't do it Steve !!
Don't Bite!!




Chet 

[altrez]

I spent about 12 hours in my shop adding my upgrades here are this morning results, I will be running tests all day long and over the weekend to see if these hold up

First I am using just 3 modules and a 60,000 uf cap.

Time         Start voltage        end voltage         Cap voltage

8:30 am     2.106 volts             2.256 volts          .562 volts
9:00 am      2.115                    2.256                  .563
9.15 am      2.136                     2.261                  .573
9.45am       2.199                    2.285                   .555
10 am         2.202                     2.290                  .540
10:15 am    2.195                    2.276                   .539
10:30am     2.213                    2.285                    .538

The ending voltage is the voltage after 15 minutes when I disconnect the cap. I short out the cap during that time to restart from  a 0.00 reading of the cap.
The test is now done for 60 seconds not 1 hr or 3600 sec.

The device has always showed a increase in voltage even after running the load.
using  E= 1/2 cv (squared) and dividing by 60 sec. wattage is now .145 watts 
Also these three are now running in series. Adding modules in parallel will increase the wattage.
It's a mystery.
Bill     

Looking good How long does it take to fill a cap to one of the starting voltages? Say this one "10:30am 2.213"? If my math is right then its just about 1 hour?

Thanks!

-Altrez