Kapanadze Cousin - DALLY FREE ENERGY

[T-1000]

http://www.liveinternet.ru/users/edward_lee/post241427460/

"
Я никуда не делся)))
   
Ð'ыло много рабоÑ,Ñ‹, одной усÑ,ановкой сыÑ, не будешь)). Ð'ечерами если позволяеÑ, время делаю еще одну.
ТуÑ, очень многие рассказываюÑ,, чÑ,о эÑ,о Ñ,,ейк)) ну , чÑ,о же у каждого есÑ,ÑŒ свое мнение и его не изменишь, Ñ...оÑ,я наверное Ñ,ак даже лучше - мне спокойнее.))
Я ни в чем не собираюсь никого убеждаÑ,ÑŒ, эÑ,о как я понял из личной переписки бесполезное заняÑ,ие, и даже если человек и собираеÑ,, Ñ,о свеÑ,иÑ,ься не будеÑ,, эÑ,о опяÑ,ÑŒ же Ñ,аки из личной переписки.
Ð'оÑ, Ñ,акие Ñ,,акÑ,Ñ‹.
Я конечно резульÑ,аÑ,Ñ‹ измерений сюда выложу, но я думаю , чÑ,о эÑ,о все чем смогу Ð'ам помочь.
С уважением.
"

Translation:
"
I did not disappear ))
There was lots of work, with one device you wouldn't stay around. ) In the evenings if there is time I am doing one more device.
There are many who are saying that it is fake ) Well, everyone has own oppinion and you cannot change it. Maybe that is even better - I am less disrupted. )
I am not going to proving for anybody, this is worthless thing from how I understood from private mailing chats and even man is assembling device, he wouln't not expose himself, this is again from private mails with people.
This is how are the facts.
I will provide measurement results here but that is only how I can help you.
Regards.
"

[verpies]

I build a small nano-pulser which was earlier proposed by verpies using a LT1073 dc-dc converter chip for testing the ability of my scope to "see" nano pulses.
Perhaps useful for other builders to test their equipment as well.
Video: http://www.youtube.com/watch?v=s-Alj7gm0RA&feature=youtu.be

Well, I have to write that I am impressed.
Getting nanosecond pulses on that crummy prototype board is extraordinary.

What value of C1 did you end up using?
What was the DC bias voltage at the top of the 1MΩ resistor?
How short did you keep the leads between C1, Q1 and that 50Ω resistor ?

[verpies]

I will provide measurement results here but that is only how I can help you.

Thanks for translating it - I appreciate how much work that is.

I think that the measurements and a schematic that these measurements refer to, constitutes essential information.

@T-1000 <-- Could you please ask this guy to point us to the up-to-date schematic that his measurements refer to.

Also, the construction details of any non-standard components are very important. Non-standard components are components, such as coils, transformers, waveguides, etc..., which cannot be bought off-the-shelf and must be self-made.

Since we have a willing russian translator here - does anyone else on this forum have any questions to Dally about his "non-standard components" ?
He already described many construction details of his "main cylindrical coil".

[T-1000]

@T-1000 <-- Could you please ask this guy to point us to the up-to-date schematic that his measurements refer to.

We need to wait until Dally will assemble second device and will provide measurements. Everyone are looking for this

[itsu]

Well, I have to write that I am impressed.

verpies,

C1 consists of 3x 10pF caps in series (see picture) so theoretically it should be around 3pF.
I also tried 4 cm of intertwined wire which worked, but was not as stable.

The DC bias voltage at the top of the 1M ohm resistor is 91.5V with a sawtooth wave on top of 2.4V p2p at 1.3Khz

Concerning the lead length, see picture.
I have changed the 50 Ohm resistor (R4) into a fixed 100 Ohm and a variable 100 Ohm in series, so
the puls is now 8V at the same 3ns width.

Regards Itsu