Kapanadze Cousin - DALLY FREE ENERGY

[TEKTRON]

   It was said that the tl494 was widely used in smps's. 4 down and all I have found is nada or a dna1002 which really seems to be a replacement for it. Can anyone confirm this? None local to be had so will have to order o/l otherwise.

thay

Thay, is this what you're looking for?
http://www.mouser.com/Search/Refine.aspx?Keyword=TL494&gclid=CLvnw9XvxbcCFWFyQgodWTwA9g

[forest]

Thay, is this what you're looking for?
http://www.mouser.com/Search/Refine.aspx?Keyword=TL494&gclid=CLvnw9XvxbcCFWFyQgodWTwA9g

Can be found  in old computer switched power supply , but more in AT based (very old)

[NickZ]

  @menofFather:
     Look at this video, from Tiger (possibly).  Is this showing a self runner?  Looks like a simple feed-back path back from the center tapped coil back to the primary coil circuit.  The main thing is it self running, or not.
It shows a circuit very similar (primary coils) to my version of the Lasersaber 2.0 Joule Ringer circuit that I'm currently using, but with some filter caps, a resistors or two, but other than that it is very similar to my set up. Although wired totally different, with center tap from the output coil going to ground. 
There is a clear diagram, and sharper focused video for a change.
  http://www.youtube.com/watch?NR=1&v=HJ0yrCKafaQ&feature=endscreen

  If Gansha is corrent then Akula was replicating some of Tiger's work, but I think that there is a
lot more that we don't know, yet, nor are either one of them telling us.
 
  I have gotten NO reply to my e-mail from Akula,  which also makes me think...that this is a serious no joke device, and from which there will not be any further information (freely) given. As it may also really have been sold, as was mentioned. 

[T-1000]

  @menofFather:
     Look at this video, from Tiger (possibly).  Is this showing a self runner?  Looks like a simple feed-back path back from the center tapped coil back to the primary coil circuit.  The main thing is it self running, or not.
It shows a circuit very similar (primary coils) to my version of the Lasersaber 2.0 Joule Ringer circuit that I'm currently using, but with some filter caps, a resistors or two, but other than that it is very similar to my set up. Although wired totally different, with center tap from the output coil going to ground. 
There is a clear diagram, and sharper focused video for a change.
  http://www.youtube.com/watch?NR=1&v=HJ0yrCKafaQ&feature=endscreen

  If Gansha is corrent then Akula was replicating some of Tiger's work, but I think that there is a
lot more that we don't know, yet, nor are either one of them telling us.
 
  I have gotten NO reply to my e-mail from Akula,  which also makes me think...that this is a serious no joke device, and from which there will not be any further information (freely) given. As it may also really have been sold, as was mentioned.

Tiger had simple experiment for feedback path in his channel on http://www.youtube.com/watch?v=bcftGrBEaL0 It was similar to Joule ringer circuit in general but different from Pantiuhov's.
Ganza is trolling all around in Russian and English forums and I would keep far away from him because this guy has too much negative and missleading things in his posts(full time paid troll by special interest?).
Akula replicated most of Romanov's work if there is no NMR involved (which is suspected most).
Pantiuhov's circuit is basic resonant transformer with half sine wave and half square wave with spikes. The collection and conversion of these spikes go to second resonant LC on 10 times lower frequency where it makes induction in another part of autotransformer so the energy becomes usable again and is fed back to same circuit. That also express itself in Grumage's first try with 30 seconds of self-sustaining run time. This circuit will be improved and one day you might see successful replication of basic principle.

Hopefully it will be more clear for now...

[dllabarre]

T-1000
In this schematic. 
Based on L2 wire length the calculated resonate freq of L2 is 24.1mHz.  You confirmed this a few days ago with me.


What freq should the L2C2L3 tank circuit be?  24.1mHz?
I have L2 & L3 inductance values.
I'm trying to determine what value C2 should be.
If I know the inductance and freq I can calculate the size (Farads) of C2 using an online LCR calculator.


Thanks for your help
DonL