Kapanadze Cousin - DALLY FREE ENERGY

[anandml]

If it is possible to make a device more than 5 Kw output with the help of induction principle and  Frequency is not a problem.  Naudin got 2 Kw output. Any one please tell me currently available high power devices works on high frequency..... 

[Сергей В.]

Please to All and especially Сергей В.

Please don´t post 4000x3000 pixel  sized big pictures.

Please resize them before posting to around 1024x768


Many thanks.


Regards, Stefan.(admin)

to Stefan
Thanks Stefan for edit of my schematics. It's good to know to rescale all pictures on 1024x768 pictures !!

Regards
Сергей В.
........................................

to all

Akula0083 channel have been wiped out from JewTube. Backup of videos you can find on Yandex.ru and some of them on den channel
http://www.youtube.com/user/131313den
........................................

1st. sch. is about Akula last video
GEDC0116PC akula0083 free energy mega device - Russian
http://www.youtube.com/watch?v=IoyTQmcEN9w

akula0083 - Free Energy1150W part2 english 
http://www.youtube.com/watch?v=BvTWKHoncK4

........................................
2nd. sch. about his first device - Russian
http://www.youtube.com/watch?v=7C4yEAm2ue4

akula0083- Free Energy 750W no battery no ground - english  from StiveP channel
http://www.youtube.com/watch?v=cUVvZzeDe5U

........................................

обсуждение схемы Акулы - discussion about Akula sch. 35,7 МБ  - Russian
https://disk.yandex.ru/public/?hash=FTcFBIZpfV0CxODOxym8CrzEnWS0azZHJmViJl8Nm3s%3D

[NickZ]

  I had mentioned previously that it had been the big diagram that Cepren had uploaded that had caused it's removable, and that I had made a proper resize of it in case that anyone needed to see it again.
 
  Cepren B.: Thanks for the hand-drawn diagram, it does help a bit, although no component values or coil turn counts are known.  It is showing the three turn yoke coil being earth grounded, and then going to the capacitor. However the center tap of the yoke coil is shown going nowhere. Could this be the case? I don't see how it would work that way. In any case, I'll study the diagram some more. The other schematic posted below it is not understandable to me. Maybe Grum can get a better grasp on it.
  Has anyone on the Russian sites or forums made a working replication of the Akula device(s)?

  All of Akula 0083 videos are still on you tube, even if his channel is not.
http://www.youtube.com/watch?v=TA3bg55qQXw
  If you look to the right of the above page, most all his videos are there.

  Thanks for the latest UFO info.
                                                 
                                                    NickZ

[Grumage]

Dear Nick.

The drawing posted is just a slightly more complicated version of the scheme I am currently working with.

L1 is the "Tesla" primary winding, which is running at a frequency designated by the variable frequency drive chip IR 2153. But what is interesting to note that a spark gap is employed to superimpose a wide band of frequencies onto the 3 turn transformer that feeds L1!! Verpies "shotgun" approach.

L2 L3 and L4 L5 are the standing wave coils and are modulated at 50 Hz by the lower IR 2153 chip.

A Ferrite Sausage of a permeability 2000-3000 probably runs through the core.

Finally L6 is the output coil to load. The only bit missing is a means of providing the feedback to self power!!!

The net result is yet another similar circuit that dear Forest clearly pointed out a few posts above this one.

Now the schematic posted by The Cell.....http://www.overunity.com/12736/kapanadze-cousin-dally-free-energy/msg363966/#msg363966.. If you have a look at the specification of Nanoperm it contains a veritable smorgasbord of NMR ingredients!!

For my own project, progress is slow but sure. I am greatly indebted to the help and time given by T-1000. We spent two and a half hours looking for that elusive resonance!! When found it was far too high, so we called it a night. Today saw a Ferrite slug placed within my resonator to lower the frequency, but alas, a greater voltage wrecked the dilectric again!! So tis back to the drawing board. I need to find a suitable material for the inner capacitive sleeve. What was interesting though, is that a modulation frequency applied via my Signal generator at 12 V p/p to the standing wave coils actually influenced the Free wheeling resonator within the capacitive liner. This was an unexpected find and would give some credence to the Hendershot generator principle.

Nos Da, Grum.

[NickZ]

quote from Grumage:
"the net result is yet another similar circuit that dear Forest clearly pointed out a few posts above this one".

  That may be, but it may also be another circuit that nobody has yet made to work, as is posted. And may also be wrong.   So, back to the wild goose chase...
 
  Also, this newer version may not have an aluminum liner, at least not one that can be seen. Or not?  If not, then so much for the Hendershot approach.
 
  In anycase we may hit on what makes this all tick, if only by accident, after weeks or months, of trying this and that. As these diagrams are still lacking many details.

  I'm hoping and counting to see our Russian friends advance this to the next level, soon.