Kapanadze Cousin - DALLY FREE ENERGY

[Grumage]

fast translation ... Presents a detailed video for electrometer . Power local radio station ( went and asked the attendant to put 5 kilowatt antenna blow , blow 4kW - save power-on . Sr.volny.Poluchaetsya r.st. ons Live - elektroveter blowing in all directions. Did MILL wind stops ? ? ? After mill ( at a distance of 100-200 meters) wind blows as well as in front of her ...
Dare ...

Dear wings DonL and All.

BINGO !! I suppose it is free energy if you do not pay to make it !! 

Cheers Grum.

[Hoppy]

Dear wings DonL and All.

BINGO !! I suppose it is free energy if you do not pay to make it !! 

Cheers Grum.

Hi Grum,

Bedini uses this reasoning for claiming COP>1 in his 'Free Energy Generation' book. A solar panel is therefore COP infinity by the reasoning that the user does not pay for the electricity produced from the solar energy. However, he appears not take into consideration that the panel may have been purchased by the user and that this not insignificant financial outlay logically needs to be built into the equation. So if a solar panel is used but has not been purchased, or the user pays for the panel from the work done by it, the electricity then produced is 'free' to the user. 

[NickZ]

   quote from Hoppy:
   "I may have missed something but I have not seen any detailed build details or for his multi-layer RMG trafo coil or drive oscillator"

   Well, that may be, but,  Geo's RMG diagram IS clear enough for me to have a wrack at it.  As well as his RMG video. 
  What details are you missing?

  I have successfully replicated his "round core" design, even without using the 5 watt zeners, etz, lighting a load of 5 bulbs of a total of 460 watts, partially lit. That's a start.

  I'm now working with Akula yoke core which I had made and wound previously, connected to my version of the Mazilli crt,  And I'll know more about that soon.
  After that, I'll be building the RMG replication, for which I already have the flyback core wound and ready to go. But, I still need more of those tuning caps.
  Geo has offered to give help and attention, where needed. That's enough for me, to continue on. I trust that he will do so, now.

  We may not see results that are OU when using less than 500 to 600 watt loads.
And the single 1000 watt halogen bulb may not provide for an optimum impedence match for the crt, either.  Maybe try 6  100 watt bulbs or so, instead.  Those bulbs have worked best for me so far...

  Itsu:  Please get back with the program, your support is much needed, as well as anyone else that wants to get their hands dirty, or not so dirty.
 
 

[Grumage]

   
   But, I still need more of those tuning caps.
   

Dear Nick.

Do you have any CFL lamps with the capacitor still intact ? Those little cap's would be great for your tuning efforts.

I must confess I have lost my "MOJO" at the moment !! Loosing my scope to a stupid accident has really shaken my confidence !! I have since replaced it with the help of this community,, thanks again !!
But I am almost too scared to hook it up to anything exceeding 12 volts !! 

I am with you all in spirit though and I do believe there is a coherent bond amongst this little community, which I am sure, with time, will bring us to the goal !!

Cheers Grum.

[NickZ]

  Grum:
  Sorry to hear about your MOYO...
  I don't have anything but a broken analog meter. Yes it did burn the fuse which has been replaced along with a fried resistor. However, that didn't help to bring it back to life, on the amp scale. Same thing happened to Geo, as well as several others working on higher voltage circuits.
  So, please try to get your "moyo working",  and join the effort.
   Also try the RMG crt, as you won't need the yoke.

  Even if this is not the best way to go to get to where we say that we want to get to, it's a start in the right direction. At least I hope so...