Kapanadze Cousin - DALLY FREE ENERGY

[Hoppy]

Hi John. What you are calculating above would be true if the grenande coil wire length
is taken as a full wavelength. That is where part of the confusion lies.  Should we
be taking the grenade coil wire length to be a quarter wave, half wave, or full wave?

I think we have to take it at 1/4 wave based on the 37.5m wire length. We also need to specify whether frequency measurements are taken with coils loaded or unloaded, as this is I think causing confusion.

[MenofFather]

Is that with the grenade coil loaded or unloaded?

Unloaded and loaded. With loaded, I remember, is same frenquencies.
Akula also scaning and searching unloaded frenquencies, he not schaning loaded coil in his video.

[Void]

Shore.
In 12 V system he use 1.5-1.6 megaherc.
In 24 V system tesla coil frenquency is 1.6 megaherc. Lengh of granate in this divice is 37,5 meters.

Thanks MenofFather. The confusion for me is where Ruslan has mentioned previously
about using a tesla coil frequency of about 2 MHz, for example on about Oct3 or 4, Ruslan
wrote the folling in the realstrannik forum (using Google Translate):
"The ground wire must be at least 16 squares and held as far as possible from vandals.  Soprativlenie may be
in the range of 1.2 to 8 ohms.  Everything will work.   Just say that the scheme will be that on the video. 
Output frequency 32 kHz, 2.012 MHz BB, work on the floor period, resistive load - light bulbs 4 x 500 Watts
(6 pieces and will try to stick as gather). "

Above Ruslan mentioned 2.012 MHz for the tesla coil frequency.
I think 2 MHz has been mentioned elsewhere as well. 1.6 MHz
has only been mentioned very recently, from Ruslan's internet conference
I believe.
All the best...

[Void]

I think we have to take it at 1/4 wave based on the 37.5m wire length.
We also need to specify whether frequency measurements are taken with coils loaded or unloaded, as this is I think causing confusion.

Hi Hoppy, based on Ruslan's comments, the calculations are based on wire length, so
loaded or not loaded would not apply, unless you mean for the tesla coil where that
does matter. Yes, the 37.5m length would seem to imply that Ruslan took the wavelength
of 2 MHz and divided by 4 to get his quarter wavelength wire length.
All the best...

[MenofFather]

Thanks MenofFather. The confusion for me is where Ruslan has mentioned previously
about using a tesla coil frequency of about 2 MHz, for example on about Oct3 or 4, Ruslan
wrote the folling in the realstrannik forum (using Google Translate):
"The ground wire must be at least 16 squares and held as far as possible from vandals.  Soprativlenie may be
in the range of 1.2 to 8 ohms.  Everything will work.   Just say that the scheme will be that on the video. 
Output frequency 32 kHz, 2.012 MHz BB, work on the floor period, resistive load - light bulbs 4 x 500 Watts
(6 pieces and will try to stick as gather). "

Above Ruslan mentioned 2.012 MHz for the tesla coil frequency.
I think 2 MHz has been mentioned elsewhere as well. 1.6 MHz
has only been mentioned very recently, from Ruslan's internet conference
I believe.
All the best...

Ruslan first say in video that kacher frenquency is 2 megaherc (in 12 volt system). Then I ask in forum "Realy 2 megaherc kacher frenquency?" Then he made new video and say in that video, that kacher frenquency in that divice is 1.5-1.6 megaherc. 


In that video (earlier video), Ruslan say that kacher is on 2 megaherc. https://www.youtube.com/watch?v=iyDaVspeeNE&list=UU_zn0cdzv_qfsxQUm4e7R9w

In that (latter video) he saying "... concrete in this tesla coil frenquency is something 1.5-1.6 megaherc": https://www.youtube.com/watch?v=xOc-7EXMvNc&list=UU_zn0cdzv_qfsxQUm4e7R9w