Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Kapanadze Cousin - DALLY FREE ENERGY

Started by 27Bubba, September 18, 2012, 02:17:22 PM

Previous topic - Next topic

0 Members and 101 Guests are viewing this topic.

NickZ

  Hey Void:
   You've been lost in space,  as well?  Good to see you posting here again.
   Could use a few more replicators around here. Gets a little lonely, at times...

magpwr

hi everyone,

This is my final hardware upgrade for the Tesla-Transponder Experiment.
After this stage i will be experimenting with harmonics base on new winding for my special tesla coil at later stage then finding suitable harmonics which would match with harmonics of the kapanadze coil. :) ;) :D 8) .

If it was resonance we can easily apply formula as what was taught.But since i am playing with harmonics only the spectrum analyzer can reveal if there is interaction between low and high frequency harmonics which is fixed eg:kapanazde coil. :D :D :D .This is the hint.

The primary goal in replacing 2 vital components capacitor and another version of SIC Mosfet resulted in reduced power consumption and at the same time increasing Amps reading to the ground.
This after finding the sweet spot which my 1KV variable Air capacitor yielded the best result.I then replaced this capacitor with a fixed value 68pf 2.5KV High Q,Low ESR Capacitor suited for use in RF or pulse application.
Replacing the capacitor did reduce power draw a little more from previous experiment nearly 20watts.

The final upgrade in order to further reduce power consumption is to replace the High Current Mosfet to little lower current version 40Amps pulse rating 1.2KV  CREE SIC MOSFET "C2M0160120D"
This mosfet gate capacitance mere "525pf" down from the 950pf base on previous SIC MOSFET used.
This ensure i don't have to worry too much if i have applied insufficient tantalum polymer capacitors at the IXD614 mosfet driver(23.5volts boosted from XL6009) supply rail at later stage during circuit design. :)

The Antenna coil using solid copper wire eventually needs to be replaced by coaxial cable using just the outer layer.This would increases the skin effect a lot more since surface area of coaxial cable is more than solid copper wire.
------------------------------------------------------
I am a little concern since a Russian forum site went down for couple of days or weeks.-http://realstrannik.com/forum/ustanovka-kulabukhova.html
If anything happens to this site do provide hints of new links in the comments of youtube.

Tomtech29

Hi.
just keep it up
works very nicely going forward.
- I moved last test on this circuit and I'll take my spare time for system-based. (Now it's time for a more difficult task)
a slightly different comparison:

I made a video but still nothing from others :-[
until next time.

Tomtech29

The use of rectifier diode to earth. :)
-and so it looks like it does not exist.

Tomtech29

...Today dug all this stuff on this forum and I did not know from some of my assumptions have you discussed and I day back was creating something that already was ::)

who does not ask it wanders like a blind man.
Here I come back to :Magpwr
you have a lot of behind -question for you is : to select the harmonic :I need to know what and how to do it properly ? and how do we know that it fits with 27kHz 1.70Mhz
"This would indicate that I will need additional windings to 27kHz" (because increasing amounts of uF only reduce the frequency down) or actually combines?
how it works in practice ,and whether the establishment( type of ground) has an impact on changes?
let it be here Paste: