Building a self looping "SMOT"

[LibreEnergia]

WOW - that is excellent elecar. I have my work cut out for me.  To space the two tubes I
drilled two holes in a piece of wood then cut lengthwise so there was half a hole and
it might take two or three cuttings to get the right distance so the ball does not
drop and touch the board. I have holes every inch and that gives me some wiggle room
and then I put a piece of paper under the ball to make sure it never pinched the paper.

thanks elecar.......
Now will the naysayers please shut up and go away......

Now it is important to replicate this... My magnet setup is way to small...

Norman

No, the naysayers are not going away because all we see is deception presented as fact and people fall for it time and again.

The video presented by 'elecar' is in this category. Sure the device completes a single loop but I'm very suspicious of the editing at the beginning of the clip. The hand placing the ball could easily have imparted some kinetic energy to the ball to allow it to complete a rotation.

How about posting a clip which shows the balls being placed carefully into position and starting with a stationary ball, to eliminate that as a factor.

[ramset]

Powercat
I suppose that the sceptic is the much easier path to take for folks who love to win ....
you get to polk and jab from the arm of the old wooden chair and never have to worry about "your reputation" or looking like a looser
its is so very Brave and safe!

you can pull all manner of examples from your posterior and fling them at will whilst quoting "for the good of the community" !!

sigh ..............

I actually find this behavior Bizzare and a bit Insane [dillusional]
to sit in a forum where no one has ever shared a working OU device {EVER} and take this stand in this thread ??

screwy!!

I have nothing but Grattitude for men like Jouleseeker ,he does much more for this planet then the people who sit on their Butt's and throw stones at the fish in the barrel from their lofty perch's.

And  I suppose Being completely anonymous whilst throwing stones at Known persons must really be Fun................

Thx
Chet

[happyfunball]

No, the naysayers are not going away because all we see is deception presented as fact and people fall for it time and again.

The video presented by 'elecar' is in this category. Sure the device completes a single loop but I'm very suspicious of the editing at the beginning of the clip. The hand placing the ball could easily have imparted some kinetic energy to the ball to allow it to complete a rotation.

How about posting a clip which shows the balls being placed carefully into position and starting with a stationary ball, to eliminate that as a factor.

There is no indication at all of pushing in this video.   

http://www.youtube.com/watch?v=--3rugO_RMg&feature=youtu.be

Maybe you're hallucinating

[elecar]

I have got one question.   

Basic property of any OU device is that its output energy should go up with every completed cycle especially when the loop is closed and should reach some maximum value depending on various constants.     

In this case the energy of ball  hence velocity of ball should go up with the completion of every cycle and after few cycles it should become uncontrollable and should move up and fall out of  straight portion of the track.  Are you proposing any brake for it?   I didnot see any blocking plate at the end of the track in your diagram.

I think in olden days when people were designing perpetual machines,  they were proposing brakes for the machines because if output energy becomes uncontrollable the machine may break and parts may fly all over the place causing injury.

I will assume this is a serious question. Firstly I have not and still do not claim overunity . There is no deliberately fitted brake, however if you watch the video of the replication of Normans track you will see the ball being sucked into the magnet array and then rolling out of the array down the ramp.  As the ball hits the end of the ramp you see the ball momentarily slow as it exits, because the magnets are still working against the ball. Just not with the same value as gravity.
Do not worry Newton, the fabric of the universe will stay intact, a little steel ball doing some circuits of a track will leave that track if it travels to fast and will come to a stop when it hits the floor.

[powercat]

I suppose that the sceptic is the much easier path to take for folks who love to win ....
you get to polk and jab from the arm of the old wooden chair and never have to worry about "your reputation" or looking like a looser
its is so very Brave and safe!

you can pull all manner of examples from your posterior and fling them at will whilst quoting "for the good of the community" !!

sigh ..............

I actually find this behavior Bizzare and a bit Insane [dillusional]
to sit in a forum where no one has ever shared a working OU device {EVER} and take this stand in this thread ??

screwy!!

I have nothing but Grattitude for men like Jouleseeker ,he does much more for this planet then the people who sit on their Butt's and throw stones at the fish in the barrel from their lofty perch's.

Thx
Chet

You still don't get it, I'm complaining about people making claims they cannot support and that includes exaggerating and lying or misinterpreting measurements, they are many good threads on here where over-unity, self-running  is a goal, not something that had been already achieved , come on show me the thread that says  "I've done it" and they have ?

For your information I have done experiments on this forum okay not recently, But attacking me for not getting involved is typical of believers when a claim can't be proved, so instead of attacking, why not do the experiment yourself ?

The whole point of science is being able to prove what you say with facts.