Kapanadze and other FE discussion

[AlienGrey]

https://www.youtube.com/watch?v=70_xKJh91eE

https://overunity.com/17328/overunity-device-by-tanju-argun-moderated/

Wesley dear chap, your absence is deafening.  What's the latest on the Ruslan / Sergej saga?

Err Hoppy that circuit as it is wont work stuff is missing, enough stuff has been on here
to tell you you can't attract static with AC you would do better with an old TV eht coil or a perspex box full
of expanded polystyrene and a fan blowing it around, but don't dispose of it down the toilet you will never get rid of it !

https://www.youtube.com/watch?v=70_xKJh91eE

[iflewmyown]

   There has been some discussion in this thread about using the electricity stored between the ionosphere and the ground. We are standing on one plate of a large capacitor, with our heads in the dielectric looking up at the other cap. plate.
I would like to tell a story which may relate to this. A couple years ago I built a Van de Graff generator in my shop. It stood about 5 ft. tall with an 18 in. ss ball on the top with teflon top roller. It was not a great performer giving 6 in. sparks to the knuckle or the 6 in. dia. ground ball. The shop it was in was I think important. The shop had concrete floor with 6 x 6 wire mesh embedded for reinforcement. The frame was mild steel down into the ground The outside walls were corrugated painted steel siding as was the roof. Inside was first a layer of 4 in. foam insulation over which were the internal walls of corrugated steel and ceiling of the same. The original purpose was to have the shop well insulated, airtight and the inside was bright white paint on the steel. My friend came over and was observing through the doorway and we decided to experiment with the machine to make longer sparks. The first thing we noticed was it would light most of the fluorescent bulbs on the ceiling when the power to them was shut off. Then when the ground ball on it's cable was moved close it would jump away from the top ball when the spark happened with a small amount of force. I could feel myself being charged any time I was in the room with it running but usually would discharge myself on the top ball. Then I decided to see how far the spark could be made to jump if I stayed away and let the charge build. I switched it on and stood upright with my right arm and first knuckle extended about four feet from the top ball. My friend was in the doorway opposite of me with the machine between us. I could feel the charge build as usual so I just stood their waiting. All of a sudden a spark jumped from my hand to the top ball about four feet away. It felt like I had been kicked by a mule in the center of my chest and my arm was pushed back into my shoulder joint with a painful jolt. I caught my breath and used the foot switch to stop the generator. My chest and arm hurt for three days, the first day like a crush injury. My friend who had been around electrical experiments for years asked me how my ears were. The rest of me hurt so bad I hadn't noticed my ears ringing. He said the spark sounded like I had fired a shot gun in the shop. I never heard it cause I hurt so bad.
Anyway, you can gather energy when you are standing inside of a capacitor, but be careful.


Wesley, if you think any of my posts here are off topic let me know or just delete them.


Garry

[ramset]

Hoppy..

Quote https://overunity.com/17328/overunity-device-by-tanju-argun-moderated/
end quote


Aliengrey
quote
  https://www.youtube.com/watch?v=70_xKJh91e  EErr Hoppy that circuit as it is wont work stuff is missing
end quote
------------------------------------------------------
Just a note..I did speak with Luc about this fellow..he reminded me he worked hand in hand with him...and there was measurement error...
AG..perhaps you could tell what Bits were missing ??
------------------------------------

[AlienGrey]

Hoppy..

Quote https://overunity.com/17328/overunity-device-by-tanju-argun-moderated/
end quote


Aliengrey
quote
  https://www.youtube.com/watch?v=70_xKJh91e  EErr Hoppy that circuit as it is wont work stuff is missing
end quote
------------------------------------------------------
Just a note..I did speak with Luc about this fellow..he reminded me he worked hand in hand with him...and there was measurement error...
AG..perhaps you could tell what Bits were missing ??
------------------------------------

Oops not that one the other one Hoppy was talking about the one we are waiting for the third video form Wesley !

I spider wired the HexFET to a Tesla coil the gate goes no where so whats the point of the HexFET driver or the divider
circuit ? more questions than answers on that device.

This video could hold some valuable information if the iron wire part works.
quote https://overunity.com/17328/overunity-device-by-tanju-argun-moderated/]https://overunity.com/17328/overunity-device-by-tanju-argun-moderated/[/url]
end quote

[iflewmyown]

Is this property suitable for experiments?
1. buried 6000 pound copper steel evaporative cooler 120 ft. from 2.
2. 36 ft. long 16" dia. pipe buried vertical 9 ft. in ground
3. 180 ft.   4 #2 conductors buried in conduit
4. 8 ft. copper coated ground rod
5. steel framed, concrete floor, steel sided and roofed shop building


Garry