Is this the first selfrunning overunity motor w/o batteries ? Mike?s motor

[USAma]

Is its documentation availible in a single file wih all circuits and diagrams.

[Eboy]

http://video.google.com/videoplay?docid=3562588371166049574

This video does not conclusively show anything. For my mind not everything is fully explained. The battery could have been removed entirely to strengthen the validity but it wasn't. Also there is the little box sitting just underneath there with the 4 round plates on it. What is that? I understand there are upload limits regarding the video size, but this movie didn't go long enough.

I have just stumbled upon "free energy" and overunity machines in the last week and would dearly love them to be reality. But I am also a very skeptical person. Further, my technical expertise is pretty poor with regards to electronics and building such devices but I am working on it.

Further explanation of this video would be appreciated. Thanks.

[MeggerMan]

Hi,
This thread has been dead for a while now, but now I have some ideas as to how Mike got his motor to work:
I think that he created  a very basic Hortong circuit.
So if the solid state relay represents the silicon/germanium/arsenic semiconductor junction that is able to amplify the electron flow, this would explain its ability to self run. In essence you are depleting the mass of semiconductor metrial to create a vast supply of energy.

I did go a long way to creating this motor, even building an acrylic model of it.
I never got it to run as I was never happy with the magnet mouting on the rotor and never completed the circuit to drive it even though I have all the parts including the all important SSR.
So what I propose as an experiment is to:
1. provide a small amount of power into the storage capacitor via a bench supply.
2. pulse the Hall switch with a coil connected to a function generator.
3. replace the coil 3 with a bridge rectifier, cap and resistor or
wind a forth collector coil to pickup the output.

The idea here is to go down a solid state route (no motor) to find, by varying the input frequency, if switching power through the solid state relay can produce un-usual outputs.
It could certainly explain a lot of circuits that apear to draw power from no where, when all along it is possible that the silicon semiconductor material itself is being consumed and providing the energy source.
For example:
Stan Meyer's water fuel cell, SM's TPU, Mikes motor, Lutec motor etc etc.

And this(but does require tritium - heavy water poured onto a big porus diode junction):
http://www.nextenergynews.com/news1/next-energy-news-betavoltaic-10.1.html
http://www.betavoltaic.co.uk/page2.html
Its just an idea, but it would certainly explain a few things.

Regards
Rob

[one]

MeggerManI

Are  you planning  on finishing  your  motor?

I  am new here   and I  havn't read the  whole thread .     I   stopped   shortly  after  Mike  burnt  out  his  motor  then got it  running again.         I jumped to the  end  and  saw that     the  topic  has pretty much  died.   

I was  wondering  if you  are planning  on finishing   your  motor  because I  have  a theory  about magnet motors .

I have noticed  that   on the magnet  motors that seem to work   one of the  things they  often seem to have in common  is  that one set of magnets is  quite a bit bigger than the other ......  3 and a half  times bigger  seems to be    a magic number.   

I noticed that  your rotor  fills  almost all the  frame  you made .   

Common   sense would seem to imply  that  getting the   outer coil  as close to the rotor  as possable  would make  the motor stronger .      If my theory is right,  a good sized  air gap  is needed to make  the   magnetic field  " big  enough ."

As I said ......I am new here .  I  am still  mostly  reading   and  learning .     I just thought I would  throw my theory  out  there .   

Just something to think about. 


gary

[toranarod]

i