High voltage HHO by IronHead

[Hot Hydro Dady]

Well the real question is in the months that Ironhead has been playing the teacher role,
has anyone come close to replicating these initially observed effects? ANYONE???

http://www.youtube.com/watch?v=SnIJyNmI33U

Two small rods producing more LPM of HHO than I have ever experienced from a single cell.
I see lots of neutral plates and plastics in the replicants, but strangly none in this video...

~Dingus Mungus

From a neutral observant stand point...
Dingus... You can get pretty damn close to the reaction in the NS-T in the video on youtube you are refferencing to from the info that IronHead has already deceminated in his posts over the last few months. I've gotten similar results with a variac & hot water & being a C-hair within a certain amount of continuity created in the water.

This Cell was made obsolete, due to excessive current draw if I had to base it on what I saw for results in my own tests, which I.H. deceminated in his posts if you read them carefully.

IronHead is going about this in a way to allow us to progress at a "Meduim Pace"(adam sandler fans)without falling in the holes he's already found and at the same time cautioning us on what NOT to do, for our own safety... He has forgotten more than I can grasp on this subject, I would suggest, join us in the learning experience and contribute when you see fit or continue to wait for it to be "handed" out, which won't happen.

my financed .02

I agree with rapttor  at first I was skeptical but after reading all IH posts I have not found him to be misleading or to say something that just does not fit. Every thing leads me to believe IH is not tiring to waist our time! He is here to help.

[IronHead]

Wow, thanks guys  what you all said here means alot to me.
I don't even have to  bash a flamer anymore , though sometimes its fun. You guys got my back and I thank you much for that.


Ok I think you guys all understand that the less voltage leaks we have the better the outcome. I was going to talk about closing the bottom up and pump water through the plats but this requires so major cell modifications and I dont think it will show you something you do not already understand. So we will leave it for a later date when the cell is ready to be multiplied and put to use.

So pulsing is what we want to talk about  and here again we are not talking about pulsing to  amp dump in the cell like the Meyer system. We are talking about shaking the hell out of the molecules . We are starting out simple we don't need 12ghz or 1.5 THz at the moment
http://www.martin.chaplin.btinternet.co.uk/vibrat.html
http://www.martin.chaplin.btinternet.co.uk/hbond.html


Someone also asked the question are we going to use IR or UV light in this cell
at any point in time  and the answer is YES


IronHead

[Hot Hydro Dady]

Will we need a cap (same uf as the cell but an higher voltage) in parallel with our cell once we start pulsing it

[Dingus Mungus]

Not looking for a free hand out here...
I got my own hydrogen project I'm working on.

Nor am I saying anything negative about what IH is teaching you.

My point was that so far most of this 60+ page thread has been about building something other than the original displayed prototype. On top of that the assembly for the SGi cell was ultra easy, and the only thing you would need to learn about would be the driving circuit. Now its the cell thats uber complicated and you guys aren't even to the driving circuit yet. It just seems a lot less practical to me, then showing us how to build the SGi...

Also if you look at other project's notes on neutral plates you'll see lots of designs that got more efficient once the neutral plates where removed. My opinion is the new cell being built is just that, something new and not the device that got everyone so excited about this thread.

Be angry with me if you must, but I'm only stating what I see.
~Dingus Mungus

[yikes]

Dingus, you are missing the point.  I know from your work with ResinRat that you are intelligent and well-meaning, but the type of cell being worked on here is not what has caused this thread to prosper.  It is the fact that IH has been willing to help the rest of us get up to speed.  And for that, among other reasons, he has our respect.  The cells and procedures may change and evolve as we as a group do also.
Stick around,,this stuff is fun.

Soldered my very first circuit board today.  Sadly, I neglected to order all the parts needed.  It's got to be the coffee that makes me do that,,,,,it ain't the age!