Nathan Stubblefield Earth battery/Self Generating Induction Coil Replications

[john_bedini]

Miki,
Nice to here from you but go back to my link I posted and read it, then we can talk about the numbers as I like numbers. I do not know if your going to believe them,. but I let the people do them and some big companies like Raytheon
http://teep.forumco.com/topic.asp?TOPIC_ID=1003
John B

[miki02131]

Hi JB,

I read the whole thread from the link you provided. The posts seem to suggest two states for the Bedini Ferris Wheel: idle and Charge. Someone provided input values for the idle state: 12.6 Watts. However, I couldn't find any reference for the Charge state input power. Please, let us know the input value for the charge state as well.

Thanks,

Miki Out.

[john_bedini]

Miki0,
Not tested buy me but by others like Raytheon and GE and Westinghouse. I only indicated the joules being delivered to the secondary battery after regulators kicked in to not overcharge secondary batteries. I said nothing about the actual output in amperes under load but it was not what you have calculated.

The input was 1.8 amps at 36 volts 64.8 watt total input to the machine. The output was 9.2 amps at 47.2 volts or 434.2 watts and 42 foot pounds of torque at 16RPM's at the shaft to break the magnetic locks this is not the motor that you and the groups have built. I have never talked about this motor until it was presented at the conference and it was only built for Tom Bearden's 80th birthday. The center coil is over 200 pounds the side coils are 125 pounds each. As I said I allowed everybody to test it as I always make my work public and it is not the SSG machine. I have had 15 offers for this machine and I do not want or need the money.

And, that puts an end to the Watson machine which in 1984 we were all involved in. Watson got the money, I got pushed agents the wall with a gun in the face and Tom got discredited because Watson disappeared. Also all these years people said prove it, well I did in front of everybody this time with their meters.

As a matter of fact the whole machine was metered so you could see everything. The only thing that worried me was that somebody was going to get knocked out by the rotating wheel. The man that wrote that page was not kidding with what he felt.

To bad we could not accomplish this on the monopole group at the time. Time is everything Miki and the past never dies it's done again another day. There were over 350 people standing there as I told the story of the monopole groups and a little history behind the machine.

The side axial motor is something that people have been experimenting with which is called the perpetual motion holder (PMH) using barium ferrite magnets in a re-gauging mode (Raymond Radus, look him up) so the power to drive that was Five .32 ma pulses at 36 volts at idle of  8RPM's the rest being returned to the primary batteries under re-gauge mode and that was metered to see.

I got really mad when Rick grabbed the shaft and it picked him off the ground and almost took his hand off.  John let everybody measure it this time in front of the public. So even electrical engineers from university's were there nothing hidden. To bad you did not make it there. Anyway that is in the past now to be discovered in a different time when it will be excepted. Nice to here from you. If you search the internet you will find more on this machine( Bedini Ferris wheel).

As I said I only built this for Tom's birthday celebration it does allot more then stated and has been measured several times. I have made a DVD on it.

Just imagine an Earth Motor running this big, it can be done now, just need a coil that big that is why I'm working on new magnetic solid state switching device. LaserSaber, Lidmotor has already proved it in videos. My point here is that I did everything very conventional buy the book this time as I learned science must have numbers, and people want numbers well you have them. This is what Tesla talked about hooking your wheel work to nature so nobody here should give up you can do it too.
John B

[solarinstallation]

Mohr Power Solar, Inc., is an established design, service, sales and installation solar contractor, specializing in solar electricity, solar pool / SPA heating, solar hot water heating systems for residential, commercial and industrial applications.

Mohr power Solar, Inc., was founded in 1982 to promote the public awareness and supply a “ Clean Environmentally Safe Energy ” to the Los Angeles, Orange, Riverside and San Bernardino counties. In addition, our company offers products, information and expertise to our customers nationwide.

Mohr Power Solar, Inc., has performed more services and has one of the largest customer base of satisfied solar energy installation customers. Mohr Power is the first solar service and repair company to service 165,000 systems for all manufacturers.

Mohr Power is the first to have a customer base of over 35,000 solar energy installation customers.



http://mohrpower.com

[miki02131]

The input was 1.8 amps at 36 volts 64.8 watt total input to the machine. The output was 9.2 amps at 47.2 volts or 434.2 watts and 42 foot pounds of torque at 16RPM's at the shaft to break the magnetic locks this is not the motor that you and the groups have built.

John B

Hi JB,

Thanks for the information and happy to see you're doing well. These values are specific enough to point to a OU device. A ratio of 434.2 to 64.8 is unbelievably high. One of these days, I might to drop by see the Bedini Ferris Wheel and hopefully be allowed to take some measurements with my equipments. Will you be showcasing the Ferris Wheel on your next conference?

Thanks,

Miki Out.