Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Nathan Stubblefield Earth battery/Self Generating Induction Coil Replications

Started by Localjoe, October 19, 2007, 02:42:39 PM

Previous topic - Next topic

0 Members and 193 Guests are viewing this topic.

Print
Go Down Pages 1 ... 160 161 162 163 164 ... 809
User actions

Pirate88179

#805
January 09, 2008, 03:19:55 PM
@ All:

OK.  A new mA record here with the new cell!  I will be making a few posts to show some pictures of today's experiments.

Results: 8.98 mA

This is my best thus far.  This picture is of the meter on the mA setting and it was actually a bit higher (9.3) but quickly fell to 8.98.  As you will see in the following pictures in the next few posts, I wired everything together for a major test the first time out.  I was going for broke.  I tested the new cell in many different configurations while hooked to the meter reading vdc.  I finally found that I got the best vdc reading with the cell vertical, so I burried it that way.  I dumped a little water on the newly burried cell as I always do to help the soil conform to the area of the cell.  If it holds as it has in the past, my readings will go up as it dries out some.  Plus, the soil is still wet here from a lot of rain several days ago and as that dries, things should get better.

Not as good as I was hoping for but, my best to date.

Bill                          PS Freezer: nice work on your fabrication.
See the Joule thief Circuit Diagrams, etc. topic here:
http://www.overunity.com/index.php?topic=6942.0;topicseen

Pirate88179

#806
January 09, 2008, 03:24:22 PM
Here is a shot of the meter with :

1.45 vdc

I obtained this along with the 8.98 mA.

(sorry for the multiple posts but if I attempt more than 1 photo per post, it times out on me)

Bill
See the Joule thief Circuit Diagrams, etc. topic here:
http://www.overunity.com/index.php?topic=6942.0;topicseen

Pirate88179

#807
January 09, 2008, 03:29:16 PM
This is a shot of the top of the new cell as it is in the ground at this point.  I have a general overall shot of the entire setup which I will use paint and label so it is more clear to all. (I am still excited here!)

OK I'll try to post this again. It said "cannont find overunity.com"


Bill
See the Joule thief Circuit Diagrams, etc. topic here:
http://www.overunity.com/index.php?topic=6942.0;topicseen

Bruce_TPU

#808
January 09, 2008, 03:34:17 PM
@ Bill

Bravo!!  That is awesome news!  But you never gave the voltage.  What was your voltage?  ;)

EDIT:
Found it!!  We posted at the same time.

So, 1.45 volts @ 8.98 ma gives us .013021 watts. 

But to build another one would cost you what, $30 USD?

Cheers,



Bruce
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

Pirate88179

#809
January 09, 2008, 03:43:14 PM
This is a drawing/photo of the test layout used today.  If it is not clear, or anyone has any questions, please ask.  Thanks.  I am going back out to see how many leds I can light, etc.  I know it's still not a lot of power, but, still heading in the right direction.

@ Bruce:

I am glad you are getting mA now.  Blown fuse? Hey, it happens.

Bill
See the Joule thief Circuit Diagrams, etc. topic here:
http://www.overunity.com/index.php?topic=6942.0;topicseen
Print
Go Up Pages 1 ... 160 161 162 163 164 ... 809
User actions