Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Muller Dynamo

Started by Schpankme, December 31, 2007, 10:48:41 PM

Previous topic - Next topic

0 Members and 53 Guests are viewing this topic.

nul-points

Quote from: smartscarecrow on May 16, 2011, 07:40:28 PM
[...]

Regards

Gary G. Hendershot

blimey - 'Hendershot' - as in the 'Hendershot Coil'?!?

same family?
"To do is to be" ---  Descartes;
"To be is to do"  ---  Jean Paul Sarte;
"Do be do be do" ---  F. Sinatra

joao.andrade

Hi Stefan,

Both 1N4007 that are connected from the drivers emitters to ground, (TIP42C), will act as a half wave rectifier for the driver coils, as far as the rotor keeps rotating. So, as one removes the battery, the driver coil will now become a pick-up coil and the referred diodes will rectify the AC from the coils, charging the 47000uF capacitor.( or at least, increasing its discharging time.).
I think this may explain why the led keeps lit that long.

Regards,

Joao.



Quote from: hartiberlin on May 16, 2011, 04:39:18 PM
Hmm,
so where is this recovery diode exactly ?

Is it D1 or is it D2 ?

As the LED need to light up it should be D2,
but then the switch would have no effect...

Hmmm....

If it is these 2 freewheel diodes of the 2 driver coilpairs,
then this also will not light up the LED at the input of the
DC2DC converter ?

Okay resistor is almost 1000 Ohms,
so the LED light should light up until
about 2 to 3 Volts.
depending at which LED current it still shows light.

When the input LED of the DC2DC converter still has
1 mA, the 1000 Ohm resistor will have 1 Volts on it
and the LED will have the threshold voltage of about 1.7 Volts, so
it adds up to 2.7 Volts at 1 mA.
So with 2.7 Volts of input voltage the LED will still light
up with a brightness of 1 mA current through it.

The real question is now,
where exactly is this mysterious recovery diode...
See the circuit diagram below...

smartscarecrow

Quote from: nul-points on May 16, 2011, 07:51:18 PM
blimey - 'Hendershot' - as in the 'Hendershot Coil'?!?

same family?


a distant relation ...


chrisC

Quote from: joao.andrade on May 16, 2011, 08:04:24 PM
Hi Stefan,

Both 1N4007 that are connected from the drivers emitters to ground, (TIP42C), will act as a half wave rectifier for the driver coils, as far as the rotor keeps rotating. So, as one removes the battery, the driver coil will now become a pick-up coil and the referred diodes will rectify the AC from the coils, charging the 47000uF capacitor.( or at least, increasing its discharging time.).
I think this may explain why the led keeps lit that long.

Regards,

Joao.

@Joao. I think you're correct. The B-E junction becomes a forward biased junction diode when the rotor is still rotating and until the rotor speed drops significantly, the coils will still half sustain the big Cap? Thanks. Seemed like no mystery and Rom is correct.

cheers
chrisC

Dave45

Quote from: smartscarecrow on May 16, 2011, 07:40:28 PM
I am looking for an individual or perhaps a panel of individuals who have at least some personal knowledge of these developments to join me in a Skype video conference next Thursday evening on my live internet broadcast.  Examples of previous shows are available for on demand review at either http://www.youtube.com/user/SmartScarecrow or http://smartscarecrow.blogspot.com .

I am not interested in causing this person Romero any problems and would prefer his name not be referenced directly.  But many seem to think the technology presented did indeed function and I understand that quite a few are replicating the device regardless of recent developments.  That is really what I am in interested in featuring on my live broadcast.

I am not in the habit of spamming folks so if this message is considered unwanted or an intrusion, my apologies.  It is my hope that the original sender of this message had a pretty focused group of folks in mind and that within this group of people, I might find a few that would be willing to discuss this project in public and on the record.

To participate, you will need an Internet capable computer, the Skype communications software and an inexpensive web camera.  My system is able to handle a conference with up to six parties so I will have to limit my “panel” to not more than six.

Please advise if interested in participating and let me know what bullet points you consider of interesting to the discussion.  Email me at smartscarecrow@gmail.com or contact me via Skype as “smartscarecrow”.

Regards

Gary G. Hendershot
AKA:  SmartScarecrow

Maybe if you really want OU , freedom for the people  we should let this fly under the radar as much as possible at least until the replications come in.