Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Working Magnetic Motor on you tube??

Started by Craigy, January 04, 2008, 04:11:39 PM

Previous topic - Next topic

0 Members and 45 Guests are viewing this topic.

Print
Go Down Pages 1 ... 186 187 188 189 190 ... 613
User actions

hydrocontrol

#935
January 15, 2008, 10:58:46 PM
Quote from: cub3 on January 15, 2008, 10:09:11 PM
Hydro

any chance you could post smaller pic's

Ive only got dial up  :-[

Den
Sorry about that.. Changed to 800x600. Should be a bit smaller and faster.

Bruce_TPU

#936
January 15, 2008, 11:02:14 PM
Quote from: Butch on January 15, 2008, 10:45:33 PM
(Snip)
We all have our doubts about this,
(Snip)
We want to have the motor as close to a perfect copy as possible to the one in the video.
This bearing change will accomplish that.
Thanks,
Butch LaFonte

I doubt it, if what I saw in the first video is any indication.  You guys might try spinning the stator magnet faster than the rotor, this next time.   ;)

So, we all have our doubts about this, but probably not the same ones you do.   ;)

Good luck to your group,


Bruce
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

hydrocontrol

#937
January 15, 2008, 11:03:28 PM
So what happened to CLaNZeR (Sean). He posted on his site http://www.overunity.org.uk
that he got the correct magnets and posted a video of it working (?) or almost working and now all the videos on his site are dead and no updates. Hope he is okay..

amigo

#938
January 15, 2008, 11:25:13 PM
Quote from: hydrocontrol on January 15, 2008, 11:03:28 PM
So what happened to CLaNZeR (Sean). He posted on his site http://www.overunity.org.uk
that he got the correct magnets and posted a video of it working (?) or almost working and now all the videos on his site are dead and no updates. Hope he is okay..
Maybe we are eating too much of his bandwidth so he had to take them down? It's strange because when you click on a video it just opens a blank page for me, normally a plugin would kick in or an external player...

Freezer

#939
January 15, 2008, 11:26:26 PM
He posts his videos here.

http://www.youtube.com/profile?user=overunityorguk

Seems like he's a lancer guy.  ;)  I'm a civic guy myself, but like lancers.
Print
Go Up Pages 1 ... 186 187 188 189 190 ... 613
User actions