Thane Heins Perepiteia.

[CRANKYpants]

FYI 

- WE DIDN'T WIN THE "NEXT GREAT CANADIAN INVENTION" CONTEST.
PRETTY HARD TO WIN WHEN THE JUDGES WON'T EVEN LOOK AT YOUR INVENTION.

http://www.nytric.com/articles.php?nwsid=43

T

[broli]

What did you expect.

Say thane how far are things in general now. What's the roadmap to be more exact. Since I'm a bit clueless where you're heading with your lenz defying motor.

[CRANKYpants]

What did you expect.

Say thane how far are things in general now. What's the roadmap to be more exact. Since I'm a bit clueless where you're heading with your lenz defying motor.

WE HAVE 2 LICENCING REQUESTS UNDER WAY,
WE HAVE 2 OR THREE ENGINEERING FIRMS INTERESTED IN BUILDING GENERATORS,
WE HAVE A COUPLE OF MOTIVATED INVESTORS AND A CONSUTING FIRM WHO IS PARTNERING WITH US TO MANAGE THE DAY-TO-DAY OPERATIONS.

WE HAVE AN EVOLVED CONCENTRIC BI-COIL IN WHICH THE OUTPUT POWER THROUGH THE LOAD IS QUADROUPLED  (X4) 1 VOLT to 4 VOLTS! WHEN THE HIGH VOLTAGE COIL IS ENGAGED AND PRIOR TO THE ROTOR ACCELERATING. (WILL SEND PHOTOS OR VIDEO TODAY) - CURRENTLY THE ONLY WAY TO QUADROUPLE A GENERATOR'S INDUCED VOLTAGE WHILE RUNNING IS TO QUARDOUPLE THE SPEED - THIS IS NOT REQUIRED AND IS VERY EXCITING FOR US!

WE HAVE 6 OTTAWA UNIVERSITY ELECTRICAL ENGINEERING STUDENTS AND 3? QUEEN'S UNIVERSITY ENGINEERING PHYSICS STUDENTS WRITING REPORTS ON THE GENERATOR.

I AM PUTTING THE FINISHING TOUCHES ON THE NEW COIL (I_RON HAS PHOTOS BUT IS HOGGING THEM)  AND PERHAPS NEXT WEEK IT GOES TO GET SCALED UP AT AN OUTSIDE SHOP.

Thane

FINAL RESPONSE FROM THE ORNL

Dear Mr. Heins

I am responding to your request addressed to Mr. Frank Damiano.  I am aware that you have also contacted the ORNL Power Electronics and Electric Machinery Research Center and you may have received a separate response from them.  In reviewing your information we have not found a strong alignment between your request and our current research agenda.  We are unable to take on projects that are not fully complementary to our own work.  Therefore regretfully, we must decline your request for collaboration.

We wish you every success in your endeavors.

Sincerely yours,
Alan Liby
__________________________
Oak Ridge National Laboratory
Manager, Industrial and Economic Development Partnerships


Thanks Liby,

I took Mitchel Olszewski's advice and found someone local and more qualified anyway.

Cheers
Thane

Thane C. Heins
President - Potential +/- Difference Inc.

"Men occasionally stumble over the truth, but most of them pick themselves up and hurry off as if nothing ever happened..." - Winston Churchill

[i_ron]

snip

I AM PUTTING THE FINISHING TOUCHES ON THE NEW COIL (I_RON HAS PHOTOS BUT IS HOGGING THEM)  AND PERHAPS NEXT WEEK IT GOES TO GET SCALED UP AT AN OUTSIDE SHOP.
snip
Thane
snip

Two reasons Sir, one, they came through at around 600 X 400 but still said 182 Kb and wouldn't post.
Took me awhile to find out I could just save then in Canvas and it kept the 400 X 600 but put it under the 100 Kb cutoff... OK?

Second, you never answered my questions in my email reply, so there, thhhhhuuuuuuuupt

So I hope you read the list before you post these again... hehehe, but here are some I thought interesting.... note the readings are in Henries and Ohms...on the meter

Ron

[i_ron]

I AM PUTTING THE FINISHING TOUCHES ON THE NEW COIL (I_RON HAS PHOTOS BUT IS HOGGING THEM) 

Thane

COPY of private post to Thane...

Danke für die Abbildugen!

I was being a smart ass and went to a 11 X 18 mm laminated core... but only 55mm long....

It came out at 60 some ohms and .9 H

But no acceleration at any speed... so got pissed off and went back to me HBG (hildenbrand/Genesis)

So interesting to see your new core and readings!

(pic 1)

(pic 2)

The bit of black plastic is to keep them apart as there are no clamps...

What is your PCD on your rotor?  How many magnets? (I know, you have said...)

Take care Ron

Note: I had made this core before I had seen Mr T's...but I see my resistance is only half  and same
with the henries...duh also this is the same rotor that didn't work the very first tests I did... could
the pot magnets have something to do with this?