Thane Heins Perepiteia.

[SkyWatcher123]

Hi folks, ok i finally decided to try and replicate to some degree what Thane is doing. And I'm happy to say having success, the other experiments i posted in this thread now make a little more sense i think. the other experiments were focused on the setting back of the coil a distance from the magnets and this seemed to provide similar effects, maybe along the lines of what Bill Muller was doing, delayed reaction or whatever the cause using 18 guage wire. The test i just ran was with 24 guage wire at around 2000 rpm with the neo magnets right at the coil face, also i wonder if Calvin Bahlmanns power wheel was using this same effect in its operation because i believe he was using high impedance coils as well and not getting any lentz drag. Also when i use 18 guage wire and try the same thing with the magnet right next to the coil it has lentz drag when coil shorted although it seems as we go higher in wire guage or higher impedance something happens and aids the drive motor so i dont see this as being hysterisis related at this point because the 18 guage wire should do the same thing so this is something different as Thane is showing us. I am now going to wind 30 guage wire onto the core which is a bolt and see what i get.

peace love light   

[hydrocontrol]

Hi folks, ok i finally decided to try and replicate to some degree what Thane is doing. And I'm happy to say having success, the other experiments i posted in this thread now make a little more sense i think. the other experiments were focused on the setting back of the coil a distance from the magnets and this seemed to provide similar effects, maybe along the lines of what Bill Muller was doing, delayed reaction or whatever the cause using 18 guage wire. The test i just ran was with 24 guage wire at around 2000 rpm with the neo magnets right at the coil face, also i wonder if Calvin Bahlmanns power wheel was using this same effect in its operation because i believe he was using high impedance coils as well and not getting any lentz drag. Also when i use 18 guage wire and try the same thing with the magnet right next to the coil it has lentz drag when coil shorted although it seems as we go higher in wire guage or higher impedance something happens and aids the drive motor so i dont see this as being hysterisis related at this point because the 18 guage wire should do the same thing so this is something different as Thane is showing us. I am now going to wind 30 guage wire onto the core which is a bolt and see what i get.

peace love light   

Keep at it. I think you are going the right direction. The reason I think this was a couple of years ago I ran across a group of people/students on-line that were trying to duplicate a Muller motor/generator. There was a web page with a video and a contact person. When I emailed the contact person about "did they ever get it self running" the response was to watch the video and at a certain time in the video to make note of the comment about throwing the switch for the "loop". Apparently that "loop" comment was throwing the switch from the battery to generator coils at a certain speed at the which point it was not battery powered. The video keep going for several more minutes without any apparent slow down in the rotor. That web site stayed around for a couple more months then disappeared and the email address went unanswered. There was never enough information posted about how to replicate or any real proof offered so it appeared to be a dead-end. Until Thane's work showing some real information came around I figured it was just more smoke and mirrors. Your replication effort does show that Thane's work here has some validity and is an avenue that is worth pursuing. Good work. Been awhile since we heard from Thane. Hope all is well.

[SkyWatcher123]

Hi folks, Hi hydrocontrol, thanks for the reply and it doesnt surpise me about the dead end in regards to the Muller generator those folks were replicating, seems alot of that has occured in the past lets hope the now and future will be on the side of freedom. I'm winding the other 30 guage coil/core right now but heres a pic of the crude test setup with the 24 guage coil/core and those are 1" dia. neo's 3/4" deep.

peace love light

[hydrocontrol]

Hi folks, Hi hydrocontrol, thanks for the reply and it doesnt surpise me about the dead end in regards to the Muller generator those folks were replicating, seems alot of that has occured in the past lets hope the now and future will be on the side of freedom. I'm winding the other 30 guage coil/core right now but heres a pic of the crude test setup with the 24 guage coil/core and those are 1" dia. neo's 3/4" deep.

peace love light

Looking good. I was hoping by now that Thane would have items for sale somewhat like Dr. Stiffler did with his system. It was nice to just spend a little bit of money to jump start research with a basic platform that worked out of the box. If Thane had already made coils and cores that matched his present research I would likely purchase them provided they had a reasonable cost. I could get the rotor made locally and install the magnets myself. The coil/core construction looks a bit trickier. I did get some MOT's off of ebay then Thane switched gears to new cores and a configuration that showed more promise. I figured I would wait to the dust to settle a bit more with Thane's research before continuing. Anyway your setup is looking good.

[tagor]

If Thane had already made coils and cores that matched his present research I would likely purchase them

yes , me too , if Thane would to send coils to france , i can purchase them ?