Selfrunning Free Energy devices up to 5 KW from Tariel Kapanadze

[sparks]

The noise out of such motor would be proportional to its angular speed, since those repelling pulses would occur at a proportionate frequency.

What I am suggesting is that TK could be pinging the motor windings with a modulated kilohertz signal.  The carrier frequency (like in a vfd drive) would be imposed on the stator windings not changing in frequency but in amplitude only.  The accelerating frequency would appear to ride the carrier.  The signal waveform could be such that it is not causing the saw noise while the carrier frequency which remains the same independent of motor rpm does. As to no change in the amplitude of the saw noise this may be due to the magnetic circuit characteristics of the motor.  The magnetostriction occuring at or near saturation of the metals employed.  An increase in current not resulting in any audible frequency change.  Perhaps that is what the battery does.  Energises a set of coils that saturates the metals.  This would definitely lower the impedance of the stator coils to a high frequency input.
  It is also interesting to note that TK could simply be demonstrating Telsa's wireless power transmission.  Tesla in later years ran small motors wirelessly at the back of auditoriums while he generated high voltage high frequency from Tesla transformers on stage.  I believe Tesla was into creating electrical monopoles which radiated much more efficiently than any wave type radiation.  Unlike what he called hertzian waves which diminish in intensity with the square of the distance from the scource,  Tesla's huge proton or electron groupings did not.  Following any line of force emanating from an electron or proton there is no reduction in intensity with distance.  There is however a decrease in number of lines of force reaching a distant volume of space emanating from said electron or proton.  By packing a great number of protons or electrons into a given amount of space the probability of more lines of force reaching a distant receiver volume are greatly enhanced as compared to just moving x number of charged particles along a given path.

[Zeitmaschine]

That's just a spiel that TK has tells journalists.  Sometimes he talks about Tesla tech and sometimes about gravity and sometimes time.

But never about John Hutchison.

BTW: I believe that electric and magnetic field is caused by a 1D or 2D lag (respectively) of matter shifted in time.

More than 100 years after Tesla and we are still on the level of believing regarding the characteristics of the electric and the magnetic field.

[Grumage]

Good evening to all,

Dear sparks, many thanks for your eloquent reinforcement of the remarks I made a couple of days ago about the use of a 3 phase variable frequency inverter. As you say the modulation frequency remains unaltered as the motor runs up to speed.

Dear Verpies, you asked me to look again at the video clip.....http://www.youtube.com/watch?v=vZC5CwCTv4I&feature=youtu.be&t=30m03s

At 31.46 one of the group slows the rotor with his hand. From this view, to me it seemed that at least 2/3 of the radius of the disc was spanned with his fingers. From this I estimate the rotor discs be no more than 12 to 14 inches in diameter. But this is pure conjecture and very open for debate.

At 31.54 they demonstrate the output from the Aluminium box. Clearly this is 3 phase as the man twists one wire to a phase and then lights up the board with the remaining two. Indicating to me that there is a Single phase to Three phase inverter present because the output is 220V between phases. But what puzzles me is where does that thick 3 phase cable go to?

But that single act begs the question. If you can light up all those bulbs with just a PP3 what the devil do you need all the other stuff for??

At 36.51 TK hits the rotor with his PP3 for a short burst. I watched this a number of times and I would estimate a rotor speed of ONE revolution per second. On the next hit the rotor speed climbs slowly but surely and I for one cannot say what the acceleration is because I have no real point of reference, mainly because the video is of very poor quality.

Just more questions than answers, sorry.

Cheers Grum.

[verpies]

But that single act begs the question. If you can light up all those bulbs with just a PP3 what the devil do you need all the other stuff for??

That's a good question.  I remember asking the same one in this thread a year ago and getting a very satisfactory answer...  I am ashamed to admit that I don't remember the answer exactly but I remember that it cleared my reservations about it.

I think it concerned the field winding of the big belt driven generator.  In the third video clip, TK used a self-exciting alternator, that did not have any supply requirements for its field winding.

[a.king21]

Grum, I asked TK the question because he wanted to build a mechanical device for us first. He personally told me that the reason why he is pushing the mechanical devices is because of the debacle with the Turks. He is scared of legal action because his contract with the Turks stipulates a 20 million (I can't remember if it is euros or dollars) penalty.
As he basically comes from a new country where corruption is the norm he is scared of legal matters.
He sent me a copy of the contract, but it is in Turkish and Georgian so it was pretty hard to decifer - even using google translate.
In any case my opinion is that he has nothing to worry about because the firm he dealt with no longer exists.
He was also scared of giving his secret away and our team thinks he is burying the patented device deep inside the mechanical.
In any case, my opinion is that he uses the mechanical for high frequency switching. In our discussions the mechanical device was called hydro-mechanical.  When I asked him about it he clarified to say that it was in an oil bath.
This immediately alerted me to the need to insulate mechanical high frequency switching in oil to prevent electrical arcs.
So I base all my deductions on facts.
Remember the two patents both have high frequency switching as part of the L1 tank circuit.
Thanks Verpies for the spark size  info. It solves yet another puzzle, and virtually scientifically proves that he uses spiked back emf (radiant energy) as the basis for his devices.
In any case he told me that his devices use high frequency. (As opposed to high voltage). Obviously the HV is a by product of high frequency switching.
Now if you look at the 2004 build and the aqurium 2 you will see HV insulation on the L2 side, which is where you would expect HV to arise as a result of HF switching.
So back to the 64,000 dollar question. what do you get when you parallel up an ordinary trafo with a HV trafo?
(I know the answer).
Also what happens to the energy balance when you spin an object at say 750 rpm - to the time field and the gravity field?
(I know the answer).
Hoppy, stop taking me for a fool.