Bedini SSG - self sustaining

[Magluvin]

Maybe you have seen this page before. The real interesting part starts at image 14  titled Spark Discharge.

Mags

[plengo]

Plengo
Have you read or seen this article?

http://www.fight-4-truth.com/Schematics.html

Mags

Hey Mag,

yes I have seen it. Thanks again. Cool stuff at the TPU Prize with agents. I am ready to start replication.

Fausto.

[plengo]

some more updates:

I have been very busy with other projects too including this one at another forum (http://www.energeticforum.com/renewable-energy/3934-high-voltage-thin-air-57.html#post79648), Dr.R.Stiffler. Great stuff for those that like lots of Leds for almost nothing.

Since I am also watching the TPU her (http://www.overunity.com/index.php?topic=8586.msg222263#msg222263), I decided to give a try at my Bob Boyce Toroid and I am surprised.

There is indeed some weird effects pulsating a coil like this one with 50% duty (which I never had done really). My scope can not see the pulses really. It is very difficult to see the output pulse when things are just right.

There are so many weird effects that I will have to document a little bit better and post it here. I am also watching very closely this other forum at (http://www.energeticforum.com/renewable-energy/962-use-tesla-switch-56.html) since I love this Tesla Battery Switch thingy!

My latest 3 SSG board simply cooked and I dismantled it so that I can reuse the parts. Funny that the board cooked not the parts. Something to think about, why would such a combination of SSGs and this toroid would cause this???

I will have to design a better layout for my next 3 SSG board so that RF does not interfere one with the other.

So, for now not much to show here buts lots of researches and other projects.

Fausto.

[Magluvin]

Hey Plen
Yeah I hope it works. It would be good for everyone.  Im rigging up a big coil set into osc. with a reed and a mag. The bemf I get is pretty strong. Like a chopper circuit. With the big coils I get big current.  Anyway I tried my gates coil with just the bemf pulses from the osc, I didnt see anything on the sec. But, Im just trying stuff. I can change the freq by adjusting the reed. Its about 1000 to 8000 hz with those reeds.
But now im setting it up to store the bemf to a cap and I have a 12v relay core aired out, And Im going to put that across the charge cap. Right now with a 1 uf cap the voltage with the 12v coil its about 10v. This is all powered by the osc bemf which runs on 5v. If I raise the value of the cap, volts with the 12v coil load will rise.  Then Im going to use a big reed in that 12v coil to dump the charge cap to the gates coil. So the 12v coil reed will osc. also when the cap voltage gets high enough to trigger the reed, it dumps the cap into the gates coil then the reed is turned off due to the gates coil taking what was in the cap. So it will be a second osc. in the circuit.  If I get a cap that can hold the charge voltage to 30v with the 12v coil acros it, then I will be in the V range it is supose to work with.  The 12v coil will get hot but hopefully it will take some abuse being chopped. If it smokes, from bemf, I know, it sounds silly, then I will get a 24v from RS and retest.  lol Im trying to be like Tesla and pretend that semiconductors are not available yet other than diodes. =]
I have no clue if it will do anything but Im giving it a go. When all else fails I will do a 555 and a fet setup.

Even if it doesnt work I want to do a vid showing the chopper chop then rechop. =]

Mags

[guruji]

Hi guys it's better to do a rectifier than diodes only to charge batteries on SSG?
Thanks