Floyd Sweet VTA Replication Project

[dieter]

Hi,

...In fact, Don Watson said the magnet to be programmed was to be excited between two plates that were charged with at least 20KV (DC or AC). This would cause a 'ringing' in the barium which would last for upwards of 15 minutes.

During that time, the magnet could be subjected to a sharp pulse at roughly 260 degrees of a 60 cps sinewave. He said this was based on his own experiments and seemed to get the best results....

see:


www.linux-host.org/energy/svta.htm

[MenofFather]

Hi,


see:


www.linux-host.org/energy/svta.htm

Maybe with 20000 volts he better get results, but Floyd use 250 volts DC capasitor. So maximum voltage  Floyd use is 250 volts. Floyd all explain how condiotion and here no secrets. Who for you is authoritity, Floyd or Watson?

[marathonman]

According to HYIQ.ORG people around Sparky are lying about the magnet conditioning and someone should be able to replicate it.
i personally believe they are lying. i don't trust none of those sorry people involved like Lindemann and Tom Bearden.
all they are is coat riders making money off other people fame or ideas.
don't forget these....

[dieter]

In fact, even several Replicators said, sparky did not only disclose parts of the operation principle, but even misleaded people by fake information. From my point of view some of the replicators have given much more valuable infos than sparky himself.


That said, one must love this 80 years old guy, when you hear his wife like "is everything alright with you?" and he like "yeah we're fine, get back into the kitchen, it's something electric"... she obviously had no idea that historical things happened right there...if they happened. Well, it's whittnessed.


I would neighter rely on the infos by the don smith replication, for other reasons. A guy named Neil Weber had some good infos and offers the original magnets, that are rare to find and of which he had to buy a few dozens. See youtube.


A COP  of 1.5 Mio is pretty cool, shure. Feels a bit like a cities power supply in your pocket. 1 Watt in, 1.5 Megawatt out. Megawatt , mmmh! 


But this whole conditioning business... I'm not getting it. I have seen the "bubble" they are talking about. Basicly it's just a reversed polarity on the barium ferrite magnets center, so along the edges it's NS, but in the center SN, with a bloch wall surrounding the center. But then they say you need to "program" the magnet with a eg. 60Hz signal while the bubble is made... program? Ok, but then it is also said, the conditioning does not only consist magnetical treatment, but also pulses of HV in the magnet material (that is nonconductive...)...


All very confusing. Nonetheless, my contribution: I once put a neodym against a barium ferrite magnet, N to N. Then I watched it with the green magnet vision film. The BF had a reversed polarity area of the size of the Neodym! So this way, with the film in place (5$, wondermagnets.com), you could remagnetize the BF magnet manually (and visually) with a neodym and achieve the same bubble. If there is also a flat coil on it, providing the 60hz signal, that might work too. At least something to experiment with.
.As Floyd Sparky Sweet said, it HAS to be Barium ferrite.
As far as I see, the donut magnets inside a microwave oven are also barium ferrrite. Tho, the hole in the middle may be a problem. Also, these magnets are magnetized so perfectly, not shure if I would want to mess with them.
.Regards

[Jimboot]

In fact, even several Replicators said, sparky did not only disclose parts of the operation principle, but even misleaded people by fake information. From my point of view some of the replicators have given much more valuable infos than sparky himself.


That said, one must love this 80 years old guy, when you hear his wife like "is everything alright with you?" and he like "yeah we're fine, get back into the kitchen, it's something electric"... she obviously had no idea that historical things happened right there...if they happened. Well, it's whittnessed.


I would neighter rely on the infos by the don smith replication, for other reasons. A guy named Neil Weber had some good infos and offers the original magnets, that are rare to find and of which he had to buy a few dozens. See youtube.


A COP  of 1.5 Mio is pretty cool, shure. Feels a bit like a cities power supply in your pocket. 1 Watt in, 1.5 Megawatt out. Megawatt , mmmh! 


But this whole conditioning business... I'm not getting it. I have seen the "bubble" they are talking about. Basicly it's just a reversed polarity on the barium ferrite magnets center, so along the edges it's NS, but in the center SN, with a bloch wall surrounding the center. But then they say you need to "program" the magnet with a eg. 60Hz signal while the bubble is made... program? Ok, but then it is also said, the conditioning does not only consist magnetical treatment, but also pulses of HV in the magnet material (that is nonconductive...)...


All very confusing. Nonetheless, my contribution: I once put a neodym against a barium ferrite magnet, N to N. Then I watched it with the green magnet vision film. The BF had a reversed polarity area of the size of the Neodym! So this way, with the film in place (5$, wondermagnets.com), you could remagnetize the BF magnet manually (and visually) with a neodym and achieve the same bubble. If there is also a flat coil on it, providing the 60hz signal, that might work too. At least something to experiment with.
.As Floyd Sparky Sweet said, it HAS to be Barium ferrite.
As far as I see, the donut magnets inside a microwave oven are also barium ferrrite. Tho, the hole in the middle may be a problem. Also, these magnets are magnetized so perfectly, not shure if I would want to mess with them.
.Regards

Or we could just buy one of these . I got delivery of some of there mags the other day and their polar patterns are crazy. Strong as hell when they lock together too. http://www.correlatedmagnetics.com/minimagprinter/