Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



The Bucking Magnet Motor

Started by z.monkey, August 25, 2010, 08:52:33 PM

Previous topic - Next topic

0 Members and 21 Guests are viewing this topic.

Print
Go Down Pages 1 ... 8 9 10 11 12 ... 33
User actions

z.monkey

#45
February 14, 2011, 07:49:56 PM
Quote from: broli on February 14, 2011, 01:45:27 PM
knowledge that no armchair could ever give  :P .
Yeah, I prefer a shop stool...
Goodwill to All, for All is One!

z.monkey

#46
February 18, 2011, 07:38:42 AM
So, Broli I agree that new energy machines don't build themselves.  And you are not going to find off-the-shelf parts to simply assemble one either.  Get the tools, get the raw materials and build it.  A lot of the stuff that I have put into this machine came off-the-shelf, but the critical working parts had to be fabricated.

Someone here has the name Dream-Think-Build.  Yeah, that's pretty much it...

I got the magnets on order Tuesday.  I needed to get a #6-32 tap, and a tube of Loctite.  Got those.    Still need to get a box of #6-32 countersunk machine screws.  I've been inspecting the parts and there are some adjustments to be made.  I am going to go ahead and bottom out the relief cuts.  This gives me a little extra clearance between the magnets.  Then if I need to tighten the clearance I can use shim washers.  I want to err on the wide side in regards to the magnets.  Don't want my fancy Neo-Mags smashing into each other...

This picture is from Feb. 5, at the end of that ice storm that glazed everyone in...
Goodwill to All, for All is One!

Bizzy

#47
February 18, 2011, 12:24:43 PM
Quote from: z.monkey on February 12, 2011, 07:54:10 PM
Working down the stator disk now...
Wow I appluad your skill and inventiveness. I tried a similar design but not nearly involved as yours.
Bizzy

z.monkey

#48
February 18, 2011, 03:29:19 PM
Thanks Bizzy,

With enough brainpowers we can crack this nut...  As with any engineering problem, it just a matter of applying an appropriate amount of engineering hours.  I've been conceptualizing this for a couple of decades.  It was just last August that got the impetus to finally draw it.  Now I am less than a week away from test...

Very exciting...
Goodwill to All, for All is One!

Bizzy

#49
February 18, 2011, 03:35:48 PM
Quote from: z.monkey on February 18, 2011, 03:29:19 PM
Thanks Bizzy,

With enough brainpowers we can crack this nut...  As with any engineering problem, it just a matter of applying an appropriate amount of engineering hours.  I've been conceptualizing this for a couple of decades.  It was just last August that got the impetus to finally draw it.  Now I am less than a week away from test...

Very exciting...
Yes very exciting indeed. Like I mentioned I went down this same raod myself so I am very interested to hear about your results.
Bizzy
Print
Go Up Pages 1 ... 8 9 10 11 12 ... 33
User actions