hmm  I just posted this.  here it is again.....   ;]

Read it again, if you havnt already and tell me what you think.  ;]

here is my post on the 14th

http://www.overunity.com/index.php?topic=11009.msg290923#msg290923

And here is Romeros post just after mine

http://www.overunity.com/index.php?topic=11009.msg290925#msg290925

mags


edited to correct link.  I must have copied the wrong link from the quote in my post.  sorry   ;]

Sorry  one of my links on the previous post was not correct.

here is a repost.

here is my post on the 14th

http://www.overunity.com/index.php?topic=11009.msg290923#msg290923

And here is Romeros post just after mine

http://www.overunity.com/index.php?topic=11009.msg290925#msg290925

I must have copied the quote link within my post.  Sorry  ;]
Mags

   edit     I corrected my previous post also

Not trying to get off topic here but the Thains video bring up some interesting concepts as far as capacitance of a coil,

In Lasersaber's video of the Stublefield coil I think everyone thought that there was a galvanic reaction going on but since the copper is coated with insulation I don't think that's probable, I think that the cotton and water is increasing the capacitance using the water as a dielectric

Using a noncorrosive dielectric this configuration could be utilized to make a very high capacitance coil, with of course the trifilar windings.

Another excellent video to watch titled "Old Energy Paradigm vs New Energy Paradigm" : http://www.youtube.com/watch?v=u3gVfltiO-E&feature=related

Thane has definitely taken this concept of speeding up a generator when it is under load and clearly shows it here as well as an explanation of how this is beating Lenz to a bloody pulp

In his diagrams showing conventional versus the Lenz beater you can see the only difference appears to be more turns in the Lenz defeating setup which he calls 'regenerative acceleration'.  I think his explanation may involve a bit more but I'm sure this supports the direction we are going with winding the coils bifilar or as Bruce_TPU mentioned to get higher voltage and lower current.  I'd say this is why Romerouk wired the 7 pairs all in parallel so as to get the current back up while keeping the same higher voltage obtained with the special Litz wiring mentioned recently here.

Quote from: tanakat on June 29, 2011, 09:26:52 PM
New Thane's video / demonstration :

http://www.youtube.com/watch?v=Z1weXYivARo

I did like what he had to say in the vid.  Is this the same as what Bruce is saying?

I really have to watch the vid again. I dont recall multifilar being said in the vid, just large inductance(high voltage coil).

Could it be he is using bifi and just calling it a high voltage coil? Thane speaks of the capacitance in the coil, but not really how it is wired.

I know the theory of why a bifi has more capacitance compared to a normally wound coil.

Anyways, this is interesting as I had posted before that maybe we could just get the rotor going on just gen coils themselves, incase nobody paid attn.  ;]

Think, no lenz in approach of the mag, and a push away on the exit.  This is what Thane says in the vid.

ok, in the post a few pages ago where I had made a miscalculation on what the resistance of the coil would be with all the 7 strands in series. I re-figured and I get 98ohms. Thane quoted a 90ohm coil in the vid. Could it be? or a coinkidink?   ;]   

Man, I hope this plot gets thinner before it gets any thicker.  ;]   

Hmm 98 ohms.  Seems like a high number to get the power we are looking for at near 12v, er 18v, what ever,

But lets say 18v/98ohm=.184Amps  x 18v = 3.3watts  ?
Thats perdy good along with no lenz and a forward push on the rotor to go with it.  But seems far from lighting a 20w bulb plus motor drive coils. Seems I say, seems.  ;]

Now this is just going by the resistance of the wire. But Bruce has his theory which may be correct.

Maybe its just not a SAFE idea to speak of the increased capacitance involved or the word bifilar.  =0   ;]

lets see if its safe,  BIFI  Hey BIFIIIIee.  bifi trifi  fifi  tribi         BIIIFIIII!    bifi      lol 

Got a lil bit of work on the tests tonight, and should be somewhere hopefully good tomorrow.   Im beat.

Mags