good place to start bill.
http://www.scribd.com/doc/20532134/Early-18x-Documentation-Release

and then maybe? NILS
http://www.youtube.com/watch?v=Px2wS4RKNrY
http://www.scribd.com/doc/21060959/Near-Infinity-Spatial-Coherence-Light-System

hi Nickz .Thank you for sharing! No not every thing has been done on jt research . There is still more to do . As far as one running more than two days then i don't blame you . I have one running it self for over 2 years  with 3 leds. It loops back over 3.5 volts back to the AAA source battery and keeps it going . Any Jt i build and most everyone here can run on dead battery for months at a time if not only a couple of weeks .You will never find them in stores.especially bright dead 1 cell battery lights   Heck fugi will run 40watt cfl almost two days powered by 2500mah 1.3 volts for almost two days . We can take your bought three battery light and when its dead convert it to one cell and use just one of those dead batteries and to get twice more longer lit light.
That is SUPER Efficient if your a light nut like some of us.i can show you at least 50 Jt lights i have here at the house. One runs from a tiny super cap and is charged from a small solar cell for just 5 minuets artificial light and it will stay lit in the dark for two days. i have it under my table lamp in my bedroom .  its on now and never goes out because it's also near a window and light passing thru a red curtain keeps it running in the day too .


Nice Coil projects with wireless juice  there . What is your power input Volts .. Still One battery or more than that?

Bill . Thanks man i was beginning to think beside me and you this thread died for good . I have two of his Sec-18s . They can also run  on 1.2 volts as well as 12 .

Wilbyinebriated . I have a hard time spelling it correctly . Man you were the First one to show a CFL and camera circuit . That was My inspiration Man , Thanks for helping and you got some nice stuff you shared .

This is a photo of that Joule Screaming JT day two running a replication of Johnnydavrs or lidmotors microwave fan coil bedini no bearing Magnet motor plus a satellite picup coil with the 5 led board . so 5 leds and running another motor with led and another induction coil running  another led . I could spin another magnet on another mirror and it will also spin from the other spinning magnet and then put more pick up coils on it further away .
I also noted that at the top of the c ore junction i can light an led pickup coil there also wireless induction where they meet
. I guarantee i can make this Jt run longer than 2 days . It's a matter of bleeding some of the output into a diode cap configuration and then using another low loss germanium diode to feed back/bleed/ to source to reduce the input current . Now i could wind another coil on top of one of those two coils and do with a secondary without any loss in the circuit . You can also take it a step further and place another coil in series with the pot before it connects to the primary coil thus have a bi /tri secondary winding on that one and harness the kick there too.In these simple circuits the KEY is  more coiled transformers and caps and lowloss diodes .and in this latest Jt, gaps in the core.
Gadget

  WillyInibriated:
  The 18x documentation is exactly what I was looking for. As mentioned, I had the link to it, but I could not find it on his web site any longer.
        thank you,
                        NickZ

Quote from: kd5sgs on August 23, 2012, 10:42:30 PM
Thanks to Pirate and gadgetmall, I was able to complete the AAA Fuji Circuit.  I was playing around with a toroid touch parts of the fuji board, to my surprise once I touched 2 pins of the transformer, the light got brighter! Does anyone know why this happened?

http://www.overunity.com/12606/cvs-disposable-camera/msg333289/#msg333289

What you have done there is Short out the bias resistor . tried it and yes it's full blast . you can use a piece of wire instead but remember your current draw will be MAXIMUM and the time it runs will be short before you change battery.
If you replace those connection with at least a 1 k pot you  can fine tune it . and further mods are done across the pot legs with small caps .

  Gadgetmall:
  Sorry for the misspelling of your username, I just noticed it.
  There are more than a few of us here that are reading these post regularly. But, the reason that many are no longer building Jtc, is due to the fact  that Joule Thiefs are just not that practical, or much of a savings. Although you mention self runners, none have been shown to run and actually produce a USABLE and BRIGHT light output, that are still running, to prove the point, and that can be REPLICATED.  Dim or blinking leds are practically useless and of not much of interest to most people. If you can show a self runner that can BRIGHTLY light several leds, for months. I'll be the first to replicate it.
It seams that some people are charging up the batteries beforehand, then showing the device running AS IF it has been doing it for months. This is not the way to get anywhere with this technology.
  I tried many, many, many replications of the backward Jtc like the ones that kooler showed (video link below), with no success of having a several month running device.
I do believe that it is possible, but even he did not further pursue the self runner. WHY?  Isn't This what we all want.   Is this not a very important device to replicate?
The link to his video below is what I'm mentioning here.
http://www.youtube.com/watch?v=dplIIhCbMcE&list=UU1SeqTWSCAhBBVjY6idzBvA&index=14&feature=plcp

  On the other hand I have several solar panels to play with now, and many many used and discard Cfl, and florescent tubes of all types and sizes to work with. Some very big one, and smaller ones as well. This is where my attention is headed right now.
However, if some one produces a simple oscillator device that can self run and brightly light leds, please show it.  Mine can run for a week or maybe more, but that is no big deal. I have hundreds of AAs (not dead ones) to keep them running, but that is of no interest to me, either.
  I'm not trying to be negative, I want to produce something useable and see the results, not just toys to play with, but real practical useable devices, that are not available otherwise.
  As I've mentioned several times, China will produce any of the devices that we come up with, and at a cost that we can't even buy the parts to reproduce ourselves. Their solar garden lights don't even use a transistor, no wound coil, either,  in the last ones that I opened up. How simple is that?  Are they getting ahead of us?