Quote from: EMJunkie on October 07, 2016, 08:16:49 PM



My progress is slow on my replication of Brad's Rotary Transformer.

My research into the RT, shows a lot of inconsistencies. Some data just doesnt fit!

I have to report what Ive found, maybe we can have some comments from Brad if hes ok with correcting me and my research? Correct me where I have gone wrong?

Still at the same place: http://buildoff.hyiq.org/thread/chris-s-build-entry/

Yes, none have entered and none are showing an interest which is pretty typical around here! The loudest are always the quietest when it comes to putting their money where their mouth is!

   Chris Sykes
       hyiq.org

Good morning,from Portugal view point,03.07 am, Chris Sykes !

Sometimes you have to "shout" more than only 1 time,many times more,that you offer your own idea
resolution website !

I think(I am not stupid ) that with the given link/enderece  http://buildoff.hyiq.org/thread/chris-s-build-entry/ the number of "none" here "....none have entered and none are showing an interest ..."
will become something of the past !

But at today you has the "hyiq.org" page , how many   "main" pages you will establish for h(a)ow many ideas/concepts ? Amazon has one page/website-link,but with several 10/100/... sub-pages !


I hope for you that you will get enough "fellowers/followers" and that in future the 24h day will be sufficient long to satisfy yours and the interests of all others which will work with you or led them only informed by your delivered site information,with the freedom to give advice,from where their knowledge they have get !


Good bye and a peacefull and successfull future
                                                                           OCWL
 

Quote from: lancaIV on October 07, 2016, 10:17:27 PM

Good morning,from Portugal view point,03.07 am, Chris Sykes !

Sometimes you have to "shout" more than only 1 time,many times more,that you offer your own idea
resolution website !

I think(I am not stupid ) that with the given link/enderece  http://buildoff.hyiq.org/thread/chris-s-build-entry/ the number of "none" here "....none have entered and none are showing an interest ..."
will become something of the past !

But at today you has the "hyiq.org" page , how many   "main" pages you will establish for h(a)ow many ideas/concepts ? Amazon has one page/website-link,but with several 10/100/... sub-pages !


I hope for you that you will get enough "fellowers/followers" and that in future the 24h day will be sufficient long to satisfy yours and the interests of all others which will work with you or led them only informed by your delivered site information,with the freedom to give advice,from where their knowledge they have get !


Good bye and a peacefull and successfull future
                                                                           OCWL

Good Morning IancaIV.

I do not want any Followers or Fellowers as you termed. I want people to be independant! Be their own leader. Make their own minds up.

Trending patterns in todays world, point toward a very bad future. We must make sufficent effort now to try to curb the worst of whats to come.

Do you know why Jupiter's Moon Io exhibits Volcanic activity? - It is too far from the Sun for the Sun to be the cause!!!

But, why are Global Volcanoes going through the Roof? Scientists tell us we are going through the Sixth Great Extinction: Will Humans Survive the Sixth Great Extinction?

   Chris Sykes
       hyiq.org

Quote from: EMJunkie on October 07, 2016, 08:16:49 PM



My progress is slow on my replication of Brad's Rotary Transformer.

My research into the RT, shows a lot of inconsistencies. Some data just doesnt fit!

I have to report what Ive found, maybe we can have some comments from Brad if hes ok with correcting me and my research? Correct me where I have gone wrong?

Still at the same place: http://buildoff.hyiq.org/thread/chris-s-build-entry/

Yes, none have entered and none are showing an interest which is pretty typical around here! The loudest are always the quietest when it comes to putting their money where their mouth is!

   Chris Sykes
       hyiq.org

I would like to refer to a statement from an email you sent me Chris-hope you dont mind,as it is just a statement.

Hey Brad - Just thought I'd let you know, as prommised, my local Engineering shop, two of them, laughed at me, said that Boring a hole in the Armature would be nearly impossible without destroying the Armature.
So, I am lost, looks like this boring a hole thing is going to be a no goer...

I wonder how many people just give up because the !so called! ex-sperts say it is near impossible 
Lucky for me,i am limited only by my own abilities.
See pic's below Chris-->just done this morning for your entertainment-->11 minutes on an $85.00 dollar drill press,and the correct procedure.
Thank god for engineer shop's-hey


Brad

Quote from: tinman on October 08, 2016, 12:02:22 AM
I would like to refer to a statement from an email you sent me Chris-hope you dont mind,as it is just a statement.

Hey Brad - Just thought I'd let you know, as prommised, my local Engineering shop, two of them, laughed at me, said that Boring a hole in the Armature would be nearly impossible without destroying the Armature.
So, I am lost, looks like this boring a hole thing is going to be a no goer...

I wonder how many people just give up because the !so called! ex-sperts say it is near impossible 
Lucky for me,i am limited only by my own abilities.
See pic's below Chris-->just done this morning for your entertainment-->11 minutes on an $85.00 dollar drill press,and the correct procedure.
Thank god for engineer shop's-hey


Brad

Hey Brad - Nice work there!

Of course this is an entirely different Armature! Not pressed into the Steel Casing of the Vacuum Motor Casing. Also a lot larger by the looks!

I am most certainly not an expert! I hope you went implying I was? I most certainly do not limit myself to anything other than Facts! None should!

Brad, I did ask questions because the Facts did not add up and Questions remained. I have actually done some experiments on Vacuum Cleaner Motors that I have not released, and yes I did try to get an Armature out of the Steel Housing from where it was pressed in. Needless to say, it did not come out without damage! I had scratches on the Steel Casing and also damaged the Laminations on the Armature. The Armature securing Lugs I did have to punch out, and this did damage the Steel Housing, it was clearly visible where I punched out the Lugs.

The pressed Fit of the Armature was too tight for easy clean removal from the Steel Casing.

The numbers given still don't add up either. 3 + 3 + 4 x 2 = 20. My Armature is only 15mm across. So I guess my research is still in error. Maybe you were referring to a larger Armature?

Again, Brad I am no expert. Motors are not my strong point! I enjoy researching devices that have potential, and the RT seems as if it has...

Sadly, I am the only one asking questions! None are willing to learn?


   Chris Sykes
       hyiq.org


P.S: My specific requirement to my local Engineering Shop, was Clean No Damage scenario, out and back in.  Looking like its never been out. They were being honest, there would be visible signs of removal.

Quote from: EMJunkie on October 08, 2016, 12:55:49 AM



Hey Brad - Nice work there!

Of course this is an entirely different Armature! Not pressed into the Steel Casing of the Vacuum Motor Casing. Also a lot larger by the looks!

I am most certainly not an expert! I hope you went implying I was? I most certainly do not limit myself to anything other than Facts! None should!

Brad, I did ask questions because the Facts did not add up and Questions remained. I have actually done some experiments on Vacuum Cleaner Motors that I have not released, and yes I did try to get an Armature out of the Steel Housing from where it was pressed in. Needless to say, it did not come out without damage! I had scratches on the Steel Casing and also damaged the Laminations on the Armature. The Armature securing Lugs I did have to punch out, and this did damage the Steel Housing, it was clearly visible where I punched out the Lugs.

The pressed Fit of the Armature was too tight for easy clean removal from the Steel Casing.

The numbers given still don't add up either. 3 + 3 + 4 x 2 = 20. My Armature is only 15mm across. So I guess my research is still in error. Maybe you were referring to a larger Armature?

Again, Brad I am no expert. Motors are not my strong point! I enjoy researching devices that have potential, and the RT seems as if it has...

Sadly, I am the only one asking questions! None are willing to learn?


   Chris Sykes
       hyiq.org


P.S: My specific requirement to my local Engineering Shop, was Clean No Damage scenario, out and back in.  Looking like its never been out. They were being honest, there would be visible signs of removal.

Chris

Would you like me to show you how to get the armature out of the steel housing within seconds,without a scratch,or without having to even pop the retainer pressings out.

20 seconds-thats all it takes Chris.

As i said,there are ex-spurts,and then there are those that know what there doing,or how to do things.
Brad