170 watts in - 1600 watts out - looped - Very impressive build and video

[gotoluc]

Thanks Jeg and L192 for clearing that.

I saw a post (can't find it now) with the concern of the Arduino's ability to drive all 36 transistor.

So, no need for Pierre to go over that in the new video.

Thanks

Luc

[gotoluc]

I let Pierre know we don't need information on the Arduino
He clarified the Arduino does not have 54 I / O   
He says it has 15 inputs 0-20ma and 54 output 5volt

Just to make sure we are all on the same page.

Luc

[TinselKoala]

I let Pierre know we don't need information on the Arduino
He clarified the Arduino does not have 54 I / O   
He says it has 15 inputs 0-20ma and 54 output 5volt

Just to make sure we are all on the same page.

Luc

Just to make sure we are all on the same page... This information isn't secret, you know.

The Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.

https://www.arduino.cc/en/Main/ArduinoBoardMega2560?setlang=en

I have one right here in my hot little grubby hands, and I can confirm that it has 54 digital input/output pins, each of which can be set independently either to Input OR Output by the software sketch.

Perhaps there is something lost or scrambled in the translation from French. Or perhaps Pierre is just learning about Arduinos. Or... perhaps the manufacturer's web page, and my experience writing sketches and using the Arduino 2560 Mega, are somehow wrong. What do you think is most likely?

While each of the 54 pins, when set to Output in software, can easily handle 20 mA current at 5V, the entire board is limited to 200 mA total. So you cannot have all the 54 pins sourcing 20 mA at the same time. But as long as you stay below the 200 mA total output you can drive transistors sequentially... even 54 of them, just not all at once.

[Mem]

MEM: Obviously you like magic shows and are ready to believe whatever you see.
Which laws of physics that apply here are broken? How?
Pierre's videos do NOT show an OU device.

A real self looped OU device does not need a bank of storage batteries or super caps.

Memoryman, That's true, however there are no established rules or regulations that OU device not suppose to have  super caps.  When input  is 170 Watts and the circuit puts out 10 times more usable watts besides powering itself and circuit voltage rises on board volt meter as soon as self looping takes place. If you don't have enough practical experience to know the meaning of this? Then I should waste no more time to say anything beyond this point. 

[Mem]

Hi everyone,

The below is a English translation (from French) of a PM e2matrix received from pedro1 (Pierre) a few days ago.

Thank you for your message and to all those who wrote me.
Thank you all for your advice.
I would like to confirm I have managed to build something that seems to bypass the written laws.
I always thought there was a way around these laws, we just need to think of different ways of going about it. There's still a lot to do.
To start with, in the next couple of weeks I'm going to make another video explaining the principle of the dz generator and the problems I have encountered.
The video will be for everyone who has interest in the device.
Afterwards you will be able to help me improve it.
My daily job requires many hours of my time, so I may not have much time to write during the week but don't worry, when I do have time I'll answer.

Thank you

Pierre

If you are a person that you have more than enough financially,  you will do great good by helping Pierre financially so he can pursue he is R&D.
I wish I was in that position to help him out...