Radiant power from Solid state Tesla hairpin circuit

[evostars]

I made an advanced solid state hairpin circuit producing radiant power.

It is based on a high side switched coil (L1) producing a negative back EMF impulse.
This impulse is injected into a series resonant bifilar pancake coil (L2).
The – BEMF impulse, replaces the sparkgap.

This L2 coil also has a positive DC offset, charged by the – back EMF.
The L2 coil equals the stout bars in the hairpin circuit.

L2 is loose coupled (4,5cm) to L3 (bigger bifilar pancake coil) that is parallel resonant. So both L2 and L3 resonate on the same frequency. L2 is series resonant (low impedance, so impulse can pass to positive of power suppy, giving the L2 a kick) and L3 is parallel resonant (high impedance).

L3 is parallel loaded with a 28W 230V light bulb, that lights up brightly.
The current and voltage of L3 are in phase. This is rather unique, as it is 4,5 cm distanced from the series resonant L2 (current and voltage 90 degrees out of phase). Radiant power is produced.

Here is the link to the video explaining it all. All info that is needed for replication is included.
https://youtu.be/1Flj1i0zQ-8



Here is the link to the schematic:
https://imgur.com/a/sh1JOwE

[benfr]

Thank you for your effort.
This is worth good thoughts for you.
An good tool of learning about the said "tesla hairpin circuit", is the part from the Resonant Induction Coupling Kit "RICK" from Rick Friedrich.
This is a kit that shows how to produce overunity by 700 % in a couple of minutes. I may post about this later on this forum.

[AlienGrey]

That sounds interesting have you got a link so we can have a look, please

After looking at the said video, this one ?> https://video.search.yahoo.com/search/video?fr=mcafee&p=Rick+Friedrich+overunity+device#id=1&vid=9dded86be474335dd8c90584e4fe25ac&action=click

I think Don Smith published some info on a similar device. using the two MOSFETs RF heater circuit you can find any where on the internet you tube.

[benfr]

hello,
the link is as follows :
https://www.youtube.com/watch?v=18kOGVfkoik
No, no mosfets (I don't even know what a mosfet is !) , jusrt simple undangerous OU to multiply VOLTAGE, or AMPERAGE, or BOTH.

[nelsonrochaa]

I made an advanced solid state hairpin circuit producing radiant power.

It is based on a high side switched coil (L1) producing a negative back EMF impulse.
This impulse is injected into a series resonant bifilar pancake coil (L2).
The – BEMF impulse, replaces the sparkgap.

This L2 coil also has a positive DC offset, charged by the – back EMF.
The L2 coil equals the stout bars in the hairpin circuit.

L2 is loose coupled (4,5cm) to L3 (bigger bifilar pancake coil) that is parallel resonant. So both L2 and L3 resonate on the same frequency. L2 is series resonant (low impedance, so impulse can pass to positive of power suppy, giving the L2 a kick) and L3 is parallel resonant (high impedance).

L3 is parallel loaded with a 28W 230V light bulb, that lights up brightly.
The current and voltage of L3 are in phase. This is rather unique, as it is 4,5 cm distanced from the series resonant L2 (current and voltage 90 degrees out of phase). Radiant power is produced.

Here is the link to the video explaining it all. All info that is needed for replication is included.
https://youtu.be/1Flj1i0zQ-8



Here is the link to the schematic:
https://imgur.com/a/sh1JOwE

You should be ashamed, to promote, the information I shared with you, including details of the circuit, without giving the credits to who rightfully. Did you feel good to hear all those compliments, and did not even mention where you got the information?
Not even a single reference to me, you are a sad being.
It's people like you who do, I doubt about the real values of people.