Selfrunning cold electricity circuit from Dr.Stiffler

[Loki67671]

@All,
A little progress from Loki. Taking some steps forward I believe. There is plenty to understand. Lets see if this video will play for you.
http://www.youtube.com/watch?v=-DcgSAamMZE

Best regards,

Jim

[pomodoro]

Gentlemen, I have built a replica of Dr Stifflers SEC circuit. Its not a copy as the transistor is different its a 2n3553 , the   coil is on a toroid and tuning is via a variable cap. The inductors are of different value too.  It has  2 BAW 62 diodes for the AV plug going to a neon. The Neon lights up so I assume that it is doing something although it might not be what the Dr's is doing. The oscilloscope trace obtained by putting the probe near the output inductor looks like a large pulse followed by  2 or 3 much smaller oscillations at optimum tuning. 



After reading the 60 pages of this thread the confusion has now set in. Lets get down to the basics, what exactly is this circuit supposed to do that special about it? 
What electrical measurements can I take to prove that something special is happening?  Is it an electronic version of Frolov's spark experiments?

[scraven]

Polystyrene would be better to use in the cells than glass (less losses to di-hysteresis). Then again not as much current will get divided from the SEC. Maybe polystyrene with a very thin coating of something to jack up the capacitance.

[Lattice333]

@All    Much of Dr Stiffler?s web site has been password protected. Unfortunately I have no communication with the Doc or access to his locked pages. Has anyone got access ? Ben? Jim?

At this stage it is unclear of the Doc?s intentions for this thread. I would be highly surprised though if he did not return to at least advise his intentions.

Where are we left? Some of you are attempting replications of SEC without the benefit of having purchased a SEC15-3 board whilst they were available. To be honest - you need to pay a lot more attention to information that Dr Stiffler released.

IMO?? The reason the Doc sold 100 or so SEC15-3 circuit boards was so that people could start with an exact copy of his circuit. Everyone had an opportunity to start at the same point. Out of all the free energy researchers in the past who has ever done this before? Did Moray ? No. Gray ? No. Bedini ? No. To me this speaks of the genuine integrity of the man and his desire to see his circuit developed. Unfortunately he acknowledged that many who purchased the boards were not capable using the board as a starting point.

I purchased a SEC15-3. I replaced the transistor with a socket but have not used it much. Why?
1) I learnt much from just analyzing it ? what components were used, how were they situated, why are some tracks large and some small etc
2) It was supposedly tuned correctly and I did not want to lose the masters tuning
3) there was no tool provided to adjust the ferrite slug in the coil and others reportedly broke the slug trying
4) the circuit board is a piece of art forged by Dr Stifflers research, perhaps it will be a collectors item one day should he be awarded an energy Noble Prize one day.

In my mind if the SEC15-3 simple circuit could not be replicated without a custom circuit board then there was no point pursuing the circuit. The Gen3 circuit sounds like a more complicated beast.

The Dr did not really want people replicating the circuit because he knew they would take shortcuts and end up with a different set of results. Now the opportunity to buy a SEC15-3 board is past so a manual replication is the only option.

My point is this ? go and buy exactly the same parts that the Doc used. @Aether22 put up the parts list in reply #2253. Do not substitute parts like my friend @pomodoro has (wrong transistor, inductor, diodes and chokes). This is a receipt for going nowhere.
Buy everything online at Jameco like the Dr did except the coil.  Here?s the good news about the coil (Aether22 please note)? IMO the coil is not that critical and does not need a ferrite slug. To prove it I hand wound a rough air coil. You can tune the inductance but squashing it in your hand. Dr Stiffler will probably curse me ? but it works. See attached photos.

If you are going to replicate ? do it on a breadboard and layout the components exactly like I have in reply#2205. Note the parts I use are exactly the same as the supplied Sec15-3 (except my usual hand made coil which was wound on a building fastener ? see a previous post of mine for details).

I hope this helps someone.

[Lattice333]

@Pomodoro    You asked ?What does a SEC circuit do?? 

It excites the underlying energy lattice allowing some excess energy to be harvested.

You asked ?how do you know when the circuit is working??

When you can light a small fluro with one lead or better still with no leads (just close proximity) then you are at the start of the race. See attached photos.