Kapanadze Cousin - DALLY FREE ENERGY

[NickZ]

T-1000,

Watching Ruslan's 6-July video, I see nothing that mandates the use of a square-wave push-pull generator.  Any decent audio Public Address amplifier with an output bandwidth of 20-20000 Hertz should suffice for driving the toroid transformer.  Ruslan also alludes to the fact the TV yoke core is unnecessary, again any toroid transformer that can operate effectively in the audio range should be sufficient.  From what I can see, the only hard requirement is to make sure you fire the Tesla impulse at the crossing where voltage drops and current increases on the induction heater coil.

It is a rather lengthy video and Ruslan does a lot of talking.  If I'm in error with my assessment of his message, please do correct me.

Well, if the ferrite yoke which has almost twice the weight and volume compared to the 3 inch toroid that Ruslan is showing, both work the same, he is not showing it doing so. Or, just how well that toroid core can substitute the yoke core. Why is he not using the toroid instead of the yoke, if that's the case? And why is a toroid core NOT used in a tv? If they work the same.  I think that they don't, as their operating frequencies, are NOT the same.

  Nor do push pull oscillators and their respective circuits, work the same as non-push pull type oscillators, and their circuits. They are different, and other than the push-pull/yoke/grenade/kacher set ups, none others have outperformed them.
 
   BTW: I have several yoke cores, which costed me nothing. $0 ... Zilch. 
How much does a thick 3 inch toroid with the same mass as yoke, cost?  Or metglass cores, or Russian yoke cores.
If you can find one? 
  34 inch crt tv can have a 4 to 5 inch ferrite yoke. I had a yoke from that size tv, at one time, but now I don't.

  Ruslan again is not really showing what it takes, step by step, to obtain a self runner.  IF, his purpose was to help others in replicating and further verifying the mode of operation, of his device. But, I don't think that he cares too much about that,  at least not at this time.

[Hoppy]

  Ruslan again is not really showing what it takes, step by step, to obtain a self runner.  IF, his purpose was to help others in replicating and further verifying the mode of operation, of his device. But, I don't think that he cares too about that,  at least not at this time.

Maybe he just likes being in the limelight. 

[NickZ]

  No doubt!  And, no replies are allowed on his videos.  So, Ruslan doesn't seam to care or want to know what WE think about his device(s). Nor really interested in showing us exactly what makes them tick...

   Hoppy:  My head is still spinning from studying all of Ruslan's different circuits, schematics, videos, etz....
Not to mention any other self runners that are being shown on YT, forums, and other places.
But, I have the feeling that it's what's NOT being shown, on YT, or these forums, that is what is missing and is needed to proceed with this build.
  Secret or private forums, as T-1000 is suggesting, may be a better bet for full device disclosure.
  However, I'm here for the long run, if needed. And to support "open source" communities, like this one.

[T-1000]

  No doubt!  And, no replies are allowed on his videos.  So, Ruslan doesn't seam to care or want to know what WE think about his device(s). Nor really interested in showing us exactly what makes them tick...

From what he was saying in videos and forums it is not entirely true. He is getting thousands emails/messages/etc and that gone to the point where he is having trouble for getting one on one conversation.
Also for step by step livestream feed I already had suggestion to him just so far there is no reply. Seems he is too busy even to reply in realstrannik forum for a week or two and all what is left just to wait...

[NickZ]

  Well, that is to be expected, all the fan mail, when Ruslan is clearly stating that he has a self running 4000w looped device.  So, Now that he has the popularity, he lost interest in fully disclosing just how it works. Such as, disconneting the Kacher while running the 4000w load, to show the difference that the heterodyning of the HV, to the magnetic current, can make. Open boxes, over a concrete floor, ground wire coiled next to the device, ends of ground cable clearly shown, etz... 
 
   I agree, that Ruslan may not have the time, nor interest, to answer our questions, nor to quench our doubts.
Now with his latest push-pull circuits, and Kacher circuits not being disclosed, no diagrams, and such, we'll just have to wait.  Or continue on with the blind teaching the blind....