Overunity.com Archives is Temporarily on Read Mode Only!


Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
You also can visit us or register at my main site at:
Overunity Machines Forum



Friction heater running in my house

Started by oilpiggy, October 31, 2012, 02:25:24 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Print
Go Down Pages 1 ... 21 22 23 24 25 ... 39
User actions

hartiberlin

#110
January 10, 2013, 08:28:35 PM
Quote from: oilpiggy on January 10, 2013, 03:32:15 AM


{Q} 8) " You probably built the first prototypes with not so much heat output as now, so you probably know, what makes it now much better ?

{A} I have learned a lot from this build from the start till now.... and I am still learning. I could make a book from everything I have learned at this point.

Thank you
Gabriel

Hi Gabriel,
yes, would be great, if you could write an ebook and sell it or just give it away freely, what you like...
if you have the time for this.

Probably  you still want first to finish your build completely for youself and heating your house with it.

You new build looks great !


Regards, Stefan.
Stefan Hartmann, Moderator of the overunity.com forum

hartiberlin

#111
January 10, 2013, 08:30:30 PM
Quote from: oilpiggy on January 10, 2013, 03:56:59 AM
Here is the new build  8)

http://www.youtube.com/watch?v=RbuZRn9duYE

Well done Gabriel,
but why does it now draw 860 Watts ?

Didn´t you say that the old model was just drawing only 100 Watts ?

860 Watts is a lot of power, if you need to produce this
during wintertime via solarpanels and the sky is overcasts...

Many thanks.

Regards, Stefan.
Stefan Hartmann, Moderator of the overunity.com forum

Bruce_TPU

#112
January 11, 2013, 06:03:23 AM
To compare efficiency, I found the following numbers.   3-ton Goodman heat pump.  The kw's are for the outside unit only.

60F, 2.86 kw
50F, 2.75 kw
40F, 2.64 kw

Gabriel's Friction Heater
.860 KW
Cheers,

Bruce
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

Paul-R

#113
January 11, 2013, 09:24:35 AM
I am interested in the magnetisation, and if there is a unipolar
(or  homopolar) generator effect happening.

Presumably, the oil is non conductive. Have you tried running the
equipment with conductive salt water instead of oil?

lancaIV

#114
January 11, 2013, 10:49:19 AM
500W no load electric motor consume , 600W load electric motor consume :
the difference means heater consume as load ergo : 100W ,

this is your calculation,oilpiggy - or not ?

wmkr
         CdL

p.s.: oilpiggy wrote about 120sqm heating area and calculating with 20 ° temperature difference and conventional
        floor/wall/roof/window/door isolation I would estimate the heat energy consume with  10KW per hour
       
       source: http://www.sonnenkoenig.ch/halogenstrahler/asetid/824/product/junior.html 
       in red:"Waermebedarf" heat calculation
Print
Go Up Pages 1 ... 21 22 23 24 25 ... 39
User actions