High voltage HHO by IronHead

[IronHead]

It all starts with these videos  I made up of a quick and dirty high voltage HHO
system to show a few people here on the forums. Well I did not think this would hijack another thread (http://www.overunity.com/index.php/topic,1500.130.html)
completely and attract so much attention.But it did , so here we are.


http://www.youtube.com/watch?v=SnIJyNmI33U
http://www.youtube.com/watch?v=DoEXaNnBRPo


The HHO system is Hydrogen Oxygen production at 150F degrees 90VDC.This system is also pulsed. We will talk about that later as each build requires a different pulse to work proper. It is my belief that high voltage low current is required to break the bond of Hydrogen and Oxygen. At least on this level of production.This is a capacitor ,treat it like one when working with these voltages that can discharge rapidly.

It must stay at this temp (150F) or it will  steam very fast so it must be cooled with radiator. This is why I am running the bench system for a shot time . If I ran it longer you would see steam billow " A hell of a lot in a very short time" from the canister.

So what you are seeing is a dirty quick build bench top version of the system I run in my vehicle.. I will soon be removing this system from my vehicle ,to remove and replace the Silver with Nitronic as the Silver is breaking down .
Do not use Tungsten in this system on the oxygen side, It will dissolve.
316 stainless is good ,and Nitronic Stainless is preferred method.

People are asking me how much gas is produced .I am no scientist I build what works for a given application. So the system in my vehicle produces enough for what I need it to do , get more bang for the buck on a big block 454ci engine.

BTW "Moab"great job you are on the top of my list of just do-ers . The "Just done it" list as it were.
You did it with out a zillion question about this that and the other scientific blah blah. Keep up the good builds

This is a very complicated system to run in a vehicle.
If you want something easy and that is proven ,buy a MagDrive


Just Build It
just do it!

IronHead

[Dingus Mungus]

Need input!

[Moab]

Wonderful!

Here is a Fullwave bridge @16 amps in cold water. I have two 312 stainless cupps for conductors. 4'' 3 1/2'' This makes HHO until the water is over 170 F. After that all you get is steam. Now at about 150 F the amprage drops to about 5-7 amps. this is the sweet spot for me so far. This is not pulsed.     Moab

[h20power]

  Now we are getting into the new way that a lot of people are starting to understand. I designed a new cell just for this purpose. Using a voltage intensifier circut is my next planed cell driver, for it and it alone is hooked up to the electrolyzer. The new cell is designed to take full advantage of this no current, high voltage concept. Voltage work theory by Stanley Myers is what I have gotten into now. We think we have figured it all out. Zigouras racing has it working just fine they say. As soon as I get the electronics built I will put Joe cell and Myer's tied together with vacuum lines, the Joe cell has to come first for it is electronicly connected, and the Myers cell is totally isolated, as it should be. I will later try to market the Myer's type cell since it is way more cost effective for me to make than a good Joe Cell. Wish me luck .

[hartiberlin]

It all starts with these videos  I made up of a quick and dirty high voltage HHO



http://www.youtube.com/watch?v=SnIJyNmI33U
http://www.youtube.com/watch?v=DoEXaNnBRPo


IronHead

IronHead,
please let us know, how much electrical power you put into this ?

Is it really HHO gas ?
Can you show another video by lighting a few bubbles after a bubbler ?

This is an amazing rate of HHO production !
Please let us know more !
Many thanks !