the zero point energy molecule! savior of mankind.

[nitinnun]

the copper molecules do not have to be monatomic.

the more the copper is sepperated into individual atoms, the better it would work.
but clumps of 10 or 20  copper atoms, will greatly help.
because the more copper atom surface area, the better it works!


what i REALLY want to do, is use silicon in place of carbon.
to make something similar to this:

     O
      I
Cu-Si-Fe


this would form a crystal lattice. which would most likely have a very high electrical resistance.
yet would most likely still conduct "magnetism", though the "covalent bond chain" of the lattice.

allowing the crystal that this would make up, to work just like a glue cell.

[nitinnun]

.....i put 2 sticks of copper into an empty plastic glue bottle.
(there was some residual glue on the bottle)

i filled it most of the way with clean ground water.
(no chlorine or flouride-poison in this water!)



i hooked the 2 copper sticks up to a 9 volt battery. and left it that way for an hour or so.

i just checked it. and the water has turned a vived green color.
which tells me that lots of copper atoms have broken off into it.


i disconnected the 9 volt battery, and checked the multimeter.
this litte "monatomic copper vat", was holding voltage and amperage.

so i shorted out the 2 copper sticks for a few second, and checked again.
and the monatomiccopper vat, is recharging itself!


i think there might be a ZPE molecule-like reaction, between the copper atoms, carbon atoms, and the oxygen/hydrogen atoms in the water.

but i'm leaving the vat shorted out for awhile, to see how long it takes this living-dead recharge rate, to go away.

[nitinnun]

this is the atom allocation that i had in mind.


ironically, the electricity will not be able to travel through the glue, from one terminal to the other.
because the glues electrical resistance will be too high.

it will be the magentism that draws the metal atoms towards the terminals.
only the magnetism of the "charge-up electricity" will travel through the glue, from one terminal to the other.

[Yucca]

Yucca,

That is not a guaranteed way to make atomic colloids, far from it. Have you taken your CS to be imaged under TEM (Transmission Electron Microscope) and determine the actual particle size?

You will probably find out that your have lumps and not nanoscale particles as expected. The best effect you could possibly achieve with CS is by having 1-10nm size particles because then they are on the comparable scale as virii, plus on that size they act like antennas for Cosmic Energies as well.

There's some theory about wet electrode surface being used in connection with the applied current in the solution. Also, are you using straight wire or did you curve them into U shapes. They say that there should be no sharp edges and that U and coiled shapes work better than straight wire.

Either way I have built and experimented (and still am) with several different kinds of circuits, AC, DC, pulsed DC, solid-state Bedini, switching polarity. I am going to do a micro-controller version as well where it can monitor the conductance and adjust current/voltage. But all that is pointless without being able to actually determine particle size imho, and TEM access is expensive, $80/hr.

Thanks for the details Amigo,

I will definitely use U shaped electrodes next time I make. I have never had TEM analysis done, have looked under optical microscope and not seen clumps but that doesn't mean much. But I do know from several experiences that CS works wonders on bacterial infections. Can't speak for antiviral properties yet, I'm always worried about drinking the stuff because I don't want to wipe out my gut bacteria.

Yucca.

[Yucca]

.....i put 2 sticks of copper into an empty plastic glue bottle.
(there was some residual glue on the bottle)

i filled it most of the way with clean ground water.
(no chlorine or flouride-poison in this water!)



i hooked the 2 copper sticks up to a 9 volt battery. and left it that way for an hour or so.

i just checked it. and the water has turned a vived green color.
which tells me that lots of copper atoms have broken off into it.


i disconnected the 9 volt battery, and checked the multimeter.
this litte "monatomic copper vat", was holding voltage and amperage.

so i shorted out the 2 copper sticks for a few second, and checked again.
and the monatomiccopper vat, is recharging itself!


i think there might be a ZPE molecule-like reaction, between the copper atoms, carbon atoms, and the oxygen/hydrogen atoms in the water.

but i'm leaving the vat shorted out for awhile, to see how long it takes this living-dead recharge rate, to go away.

Nice result so far! What do you think is the purest form of copper, plumbing pipe or stripped wire? Or is there something purer?
Yucca.