Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Selfrunning Free Energy devices up to 5 KW from Tariel Kapanadze

Started by Pirate88179, June 27, 2009, 04:41:28 AM

Previous topic - Next topic

0 Members and 89 Guests are viewing this topic.

ldongder

Hi , any one knows about this Schematic attached?

In the picture,there is a spark gap(1200V) (in the green square), can we replace the the spark gap with a Bidirectional diode? Any one can propose the model and specs of the Bidirectional diode?

Another question: in the red square, what does 8m mean? 8 meters length?

Thanks and regards
Looking forward to answers:)



Utopia Now

Hello Guys I found this video on YouTube,  about magnet field lines shown on an old TV   like Floyd Sweet also showed in one of his video`s.
https://www.youtube.com/watch?v=EYf_7VRrYeU

Does anyone have a link to that video.

Very interesting to see the round Bar Magnet inside the ring magnetron Magnet.


stivep




Quote
I dig ground Approximately 80 feet into water level And put ground wire in this hole






I have never seen the ground  wire 80ft deep into the ground.
This could be  braking point in our quest for adventures    thinking. 
But it needs also  careful experienced   engineer to analyze the data..
If it was me I would go down to the pit( shaft)  80ft below the ground 
surface. place there insulated  thick  wire( at best gauge 0 -or 1 to 6) 
with the 6ft copper  rod attached . the second end of this wire would be
going up to surface  of the earth. 
For DC  there would be certain capacitance between surrounding  ground and inner wire..
If you  connect nano/ pico second square wave generator
Than rising  edge and  falling edge  of it is AC component with DC  on the top .
If we make  than the bottom  of the square wave at 0V potential ( similar to
manual or electronic braking - ON/OFF/ON and so on.)
than you creating electron inertia  in  DEAD 0V (zero volt)intervals.
For me it is  important  to see the load behavior (at the very top  end  of this wire.
According to my theory ( Wesley's Electrostatic Pump Theory)
short impulse  generator is responsible for creating  string  of  interactions
with  associated  impedance  -properties  .
Self looping ( self powering) is than effect of  coupling one energy source
( free of taxes and costs) to another.
energy conversion  has in mind:
1.  presence of mechanical inertia of   electron and its motion properties.
2. presence of  HV electrostatic potential as an attractive force for electrons to be
" sucked" from the ground.


Wesley


https://www.youtube.com/comments

Grumage

Quote from: ldongder on June 09, 2016, 10:26:31 PM
Hi , any one knows about this Schematic attached?

In the picture,there is a spark gap(1200V) (in the green square), can we replace the the spark gap with a Bidirectional diode? Any one can propose the model and specs of the Bidirectional diode?

Another question: in the red square, what does 8m mean? 8 meters length?

Thanks and regards
Looking forward to answers:)

Dear ldongder.

Welcome to OU.com.   :)

Your diagram looks very familiar...... I think it's a redrawn schematic of one of Don Smiths devices, See attached picture.

8 M, I think refers to 8 turns.

I experimented with this some years ago, sadly, for me, no OU.

Cheers Grum.